(The surface of access aisles cannot slope more than 2% in any direction)....
Search Results "Work Surface"
-
Built-up Curb Ramps [4.7.6]
-
4.1.7(3)(e)
., open books), should be no higher than 44 in (1120 mm) above the floor surface....
-
4.7.1 General
In alterations, where a condition for exception in section 1.1 prohibits full compliance with a specific requirement for clear floor or ground space surface, slope, size, or location, the...
-
Fixed tactile maps
Placement on a horizontal or near horizontal surface provides the map reader with a real world orientation....
-
6.9 Tread Obstacles
Where the surface is paved or is elevated above the natural ground, obstacles shall not exceed 1/2 inch (13 mm) in height measured vertically to the highest point....
-
Original research for ANSI A117.1 (1957 - 1961)
Buildings and Facilities Accessible to, and Usable by, the Physically Handicapped, ramps were assessed for flatness based on measuring 18 - inch increments on both edges of the ramped surface...
-
11B-704.5 TTY shelf
The telephone handset shall be capable of being placed flush on the surface of the shelf....
-
403.5.1 Clear Width
Except as provided in 403.5.2 and 403.5.3, the clear width of walking surfaces shall be 36 inches (915 mm) minimum....
-
1005.2.1 Height
At least 25 percent of the railings, guards, or handrails shall be 34 inches (865 mm) maximum above the ground or deck surface....
-
1009.5.4 Transfer Steps
The surface of the bottom tread shall extend to a water depth of 18 inches (455 mm) minimum below the stationary water level. Advisory 1009.5.4 Transfer Steps....
- ADA25: Cindy's Story
- Lilypad Wheelchair Scale
-
Typical Transfer Techniques: Staff Assistance and Patient Lifts
Other individuals will need simple tools such as a transfer board (a product made of a smooth rigid material which acts as a supporting bridge between a wheelchair and another surface, along...
-
Common Requirements (R304.5) (Section-by-Section Analysis)
Grade breaks are not permitted on the surface of ramp runs and turning spaces. Surface slopes that meet at grade breaks must be flush....
-
Transfer Supports (M301.3.1, M302.3.1, and M305.2)
M305.2.1 would require the transfer supports to be located within reach of the transfer surface and not obstruct transfer onto the surface when in position....
-
Clearance in Base (M301.4.1 and M302.4.1)
would require the clearance in the base to be 44 inches wide minimum, 6 inches high minimum measured from the floor, and 36 inches deep minimum measured from the edge of the examination surface...
-
202.4 Alterations Affecting Primary Function Areas
Such areas include but are not limited to: Remodeling merchandise display areas or employee work areas in a department store; Replacing an inaccessible floor surface in the customer service...
-
Picnic Tables
All new picnic table installations must comply with requirements for accessible seating spaces, table clearance, slope, and surface....
-
5. If there is a significant risk, reasonable accommodation must be considered
He worked in a corner of the garage, facing outward, so that he could see moving buses....
-
4.2 Overview of Legal Obligations
An employer is not required to lower existing production standards applicable to the quality or quantity of work for a given job in considering qualifications of an individual with a disability...
-
5. Service Animals
The rule defines "service animal" as a dog that has been individually trained to do work or perform tasks for the benefit of an individual with a disability....
-
5. Service Animals
The rule defines "service animal" as a dog that has been individually trained to do work or perform tasks for the benefit of an individual with a disability....
-
b. State Laws
An employer could not assert, as a valid defense to a charge of discrimination, that it failed to hire or return to work an individual with a disability because doing so would violate a...
-
Introduction
By following these guides for best practices your industry will be proactively working to give people the best possible experience....
