Search Results "Water Closet Clear Floor Space"
Filters
Commonly Searched Documents
-
MOEN M–POWER chrome electronic flush valve 1 1/2" water closet retro fit 8310R16
-
A. ACCESSIBLE SEATING
space requirements set forth in table 221.2.1.1 of the Standards....
-
3. Exception to Ramp Running Slope
The MDE Advisory Committee, during its discussion of wheelchair spaces on weight scales, extensively addressed the permissible slopes of ramps on raised platforms....
-
11B-805.2.4 Toilet and bathing rooms
Where provided, one water closet, one lavatory, and one bathtub or shower shall comply with the applicable requirements of Sections 11B-603 through 11B-610....
-
11B-609.3 Spacing
The space between the wall and the grab bar shall be 1½ inches (38 mm). The space between the grab bar and projecting objects below and at the ends shall be 1½ inches (38 mm) minimum....
-
Types of Facilities and Required Means of Entry into the Water
Types of Facilities and Required Means of Entry into the Water...
-
Ticketing (Assembly areas, not parking.)
Title II Regulations 28 § 35.138 Ticketing: (a) (1) For the purposes of this section, “accessible seating” is defined as wheelchair spaces and companion seats that comply with...
-
Floor [1014.3]
The floor surface within a camp shelter must be firm and stable....
-
11B-213.2.2 Unisex (Patient) toilet rooms in medical care and long-term care facilities
Common-use unisex toilet rooms for exclusive patient use not located within patient bedrooms shall contain a lavatory and one water closet....
-
1010.1.5 Floor elevation
There shall be a floor or landing on each side of a door. Such floor or landing shall be at the same elevation on each side of the door....
-
11B-405.4 Floor or ground surfaces
Floor or ground surfaces of ramp runs shall comply with Section 11B-302. Changes in level other than the running slope and cross slope are not permitted on ramp runs....
-
M303.1 General
Diagnostic equipment used by patients seated in a wheelchair shall comply with M303.
-
M303.3.1 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical.
-
M303.3.2 Beveled
Changes in level between ¼ inch (6.4 mm) high and ½ inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2.
-
M303.4 Components
Where components of diagnostic equipment are used to examine specific body parts, the components shall be capable of examining the body parts of a patient seated in a wheelchair....
-
F202.6.5.5 Assembly Areas
Assistive listening systems shall comply with F219 and assembly seating shall comply with F221.
-
M303.4 Components (Section-by-Section Analysis)
The MDE NPRM proposed to require diagnostic equipment used by patients seated in a wheelchair which has components that are used to examine specific body parts, be capable of...
-
M303.1 General (Section-by-Section Analysis)
This is an introductory section.
-
Key Features of Accessible Stadiums
[See subsections ...]
-
T208 Passenger Access Routes
[See subsections ...]
-
T605 Seat Belts and Shoulder Belts
[See subsections ...]
-
A2
A2. Is the vehicle pull-up area relatively level (1:50 or 2% maximum slope in all directions)? Yes No
-
A4.8.2 Slope and Rise
Ramp slopes between 1:16 and 1:20 are preferred. The ability to manage an incline is related to both its slope and its length. Wheelchair users with disabilities affecting their arms...
-
A4.8.2 SLOPE AND RISE
The ability to manage an incline is related to both its slope and its length. Wheelchair users with disabilities affecting arms or with low stamina have serious difficulty using...
