Where knee clearance is required under an element as part of a clear space, the knee clearance shall be 280 mm (11 in) deep minimum at 230 mm (9 in) above the finish surface, and 205 mm...
Search Results "End Transfer Surface"
-
R405.3.3 Minimum Required Depth
-
Illumination Levels (Reserved) [4.30.8]
A level from 10 to 30 footcandles is recommended uniformly over the sign surface....
-
11B-240.2.2 Elevated play components
For purposes of this section, ramps, transfer systems, steps, decks, and roofs are not considered elevated play components....
-
Additions: ADA Standard Section 240.1.1
Section 240.1.1 of the ADA Standards covers information in the current ADA Standards on scoping requirements for additions to play areas.
-
11B-240.2.2 Elevated play components
For purposes of this section, ramps, transfer systems, steps, decks, and roofs are not considered elevated play components....
-
Appendix D: Photometric Measurements
that would be reflected from a perfectly diffusely reflecting surface....
-
Polypavement
After uncharacteristically heavy rainfall, the surface became the same texture as mud. Upon drying up, the surface remained cracked and was heaving along the full width of the trail....
-
Camp Shelters
However, when the surface is unpaved or not built with boards, slopes 5 percent (1:20) or less are allowed if necessary for drainage....
-
Finish and Contrast: ADA Standard Section 703.6.2
Additional factors affecting the ease with which the text can be distinguished from its background include shadows cast by lighting sources, surface glare, and the uniformity of the text...
-
11B-703.7.2.7 Pedestrian traffic-control buttons
Control buttons shall be located no higher than 48 inches (1219 mm) above the ground surface adjacent to the pole....
-
11B-605.5.4 Toe Clearance
Partition components at toe clearances shall be smooth without sharp edges or abrasive surfaces....
-
11B-703.7.2.7 Pedestrian traffic-control buttons
Control buttons shall be located no higher than 48 inches (1219 mm) above the ground surface adjacent to the pole....
-
Passing Spaces: ADA Standard Section 403.5.3
Section 403.5.3 covers the current ADA Standards for passing spaces that are part of an accessible route.
-
11B-605.5.4 Toe Clearance
Partition components at toe clearances shall be smooth without sharp edges or abrasive surfaces....
-
11B-407.4.10 Support rail
Support rails in elevator cabs are used in a different way than handrails along a walking surface such as a ramp or stairway. ...
-
4(5)
(5) Exterior deck, patio, or balcony surfaces are no more than 1/2 inch below the floor level of the interior of the dwelling unit, unless they are constructed of impervious material such...
-
11B-705.1.1.3.2
Detectable warning surfaces shall provide a 70 percent minimum visual contrast with adjacent walking surfaces....
-
11B-407.4.10 Support rail
Support rails in elevator cabs are used in a different way than handrails along a walking surface such as a ramp or stairway....
-
904.3.2 Counter
The counter surface height shall be 38 inches (965 mm) maximum above the finish floor or ground....
-
4. Do the carpet requirements of Section 302.2 apply to ground level accessible routes within a play area?
Accessible playground surfaces, including turf-like surfaces, must meet the requirements of ASTM F 1951-99....
-
4.5.3* CARPET
If carpet or carpet tile is used on a ground or floor surface, then it shall be securely attached; have a firm cushion, pad, or backing or no cushion or pad; and have a level loop, textured...
-
Secondary ticket market. (Section-by-Section Analysis)
The secondary ticket market, for the purposes of this rule, broadly means any transfer of tickets after the public entity's initial sale of tickets to individuals or entities....
-
Data Analyses
Data Analyses Net energy consumption – the additional energy utilized during walking in excess of resting levels – was calculated for each surface....
-
Interactive Illuminated Models
Interactive Illuminated Models Another promising new development expands on the concept of touch sensitive talking models by projecting light onto the model’s 3D surface....