The technical requirements address the surface of the trails, passing spaces, and resting intervals (1017.2); the clear tread width of trails (1017.3); passing spaces (1017.4); tread obstacles...
Search Results "Door Clear Width"
Filters
Commonly Searched Documents
-
1017.1 General
-
804.6.2 Operable Parts
Appliance doors and door latching devices shall not be required to comply with 309.4. 2....
-
4.34.6.10* KITCHEN STORAGE
(2) Door pulls or handles for wall cabinets shall be mounted as close to the bottom of cabinet doors as possible....
-
Temporary Measures
For example, if the only entrance door at a polling place is 29 inches wide, then propping the door open or providing a doorbell for a poll worker to open the door will still not allow a...
-
11B-502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings....
-
502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings....
-
11B-502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings. ...
-
11B-703.5.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
11B-703.2.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
11B-502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings....
-
Section 2. Entrance
For purposes of these guidelines, an "entrance" does not include a door to a loading dock or a door used primarily as a service entrance, even if nonhandicapped residents occasionally use...
-
11B-804.6.2 Operable parts
Exceptions: Appliance doors and door latching devices shall not be required to comply with Section 11B-309.4....
-
11B-504.8 Floor identification
required by Chapter 10, Section 1023.9 complying with Sections 11B-703.1, 11B-703.2, 11B-703.3 and 11B-703.5 shall be located at the landing of each floor level, placed adjacent to the door...
-
11B-308.3.1 Unobstructed
Where a clear floor or ground space allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 48 inches (1219 mm) maximum and the low side...
-
Door King Inc. 9100 Slide Gate Operator Residential & Commercial
The Model 9100 operator is designed to operate vehicular slide gates in residential and commercial applications. The 9100 is designed so that it can easily be mounted in the front,...
-
Jacknob Corp. 6409 ADA Latch & Strike Combo for Inswinging Door
6409 Latch-Strike-Combo-Inswing-ADA-CRSS Satin Stainless Steel
-
Door King Inc. VoIP Integration for Entry and Access Control Systems
VoIP (or Voice over Internet Protocol) is a general term used to describe various transmission technologies, communication protocols, and methodologies that are used to provide voice...
-
Common Problems with Signs
Ø Some signs – such as permanent room signs – are required to have Braille, high contrast, and raised lettering and must be located on the wall to the latch side of the appropriate door...
-
11B-804.6.2 Operable parts
Appliance doors and door latching devices shall not be required to comply with Section 11B-309.4. 2. ...
-
11B-804.6.2 Operable parts
Appliance doors and door latching devices shall not be required to comply with Section 11B-309.4. 2....
-
1012.1 General
The technical requirements address the width of parking spaces and pull-up spaces for recreational vehicles (1012.2); the width of parking spaces for vehicles, other than recreational vehicles...
-
703.2.7 Character Spacing
Where characters have rectangular cross sections, spacing between individual raised characters shall be 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum....
-
703.2.7 Character Spacing
Where characters have rectangular cross sections, spacing between individual raised characters shall be 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum....
