Back support shall be 48 inches (1219 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (457 mm) minimum above the seat...
Search Results "Ramp Surface"
-
11B-903.4 Back support
-
Accessible routes
Accessible routes that coincide with, or are located in the same area, as general circulation paths and elements such as ramps, elevators, and fare vending and collection must be placed...
-
2.2 Entrances
If there are stairs at entrances, are there also ramps or lifts? Can the accessible entrance be used independently, or is the door heavy or usually locked?...
-
1012.3 Other Vehicles
This section requires parking spaces for vehicles, other than recreational vehicles, to be 16 feet wide minimum to accommodate vans equipped with a lift or ramp....
-
11B-809.7.2 Changes in level
Ramps complying with Section 11B-405, elevators complying with Section 11B-407 or platform lifts complying with Section 11B-410 shall be provided where changes in level exceed 1/2 inch (...
-
A. Accessible Voting Program
condition on Election Day those features of facilities and equipment (including, but not limited to, permanent equipment such as lifts and elevators, and temporary equipment such as portable ramps...
-
Mockett DH4/DH5 Installation Video
Lightweight, yet sturdy and durable, these subtle complementary pulls will enhance the overall design of any door surface....
-
Tread Width
The visible trail surface measured perpendicular to the direction of travel....
-
801.1 Scope
For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
-
801.1 Scope
For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
-
M301.4.2 Clearance Around Base
The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
903.4 Back Support
Back support shall be 42 inches (1065 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (455 mm) minimum above the seat...
-
M302.4.2 Clearance Around Base
The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
Accessible Parking
This route must have no steps or steeply sloped surfaces and it must have a firm, stable, slip-resistant surface....
-
11B-206.7.9 Team or player seating
While the use of platform lifts is allowed, ramps are recommended to provide access to player seating areas serving an area of sport activity....
-
11B-206.7.9 Team or player seating
While the use of platform lifts is allowed, ramps are recommended to provide access to player seating areas serving an area of sport activity. ...
-
11B-206.7.9 Team or player seating
While the use of platform lifts is allowed, ramps are recommended to provide access to player seating areas serving an area of sport activity. ◼...
-
Rebuilding Together Dayton - Dayton, OH
We also provide urgently needed safety updates, such as wheelchair ramps, grab bars, and hand-rails, by skilled tradespeople....
-
AbilityApp
Disability friendly features at specific locations will be listed like wheelchair ramps, Braille signs and menus, service animal relief locations, assistive technology for the hearing impaired...
-
Rebuilding Together North Jersey - Ridgewood, NJ
programs include National Rebuilding Day (the last Saturday in April), Fire Safety (smoke- and CO-alarm installations and fire-safety education), and Critical Needs (primarily accessibility ramps...
-
Transition Plate
A sloping pedestrian walking surface located at the end(s) of a gangway....
-
106.5.72 Transition Plate
A sloping pedestrian walking surface located at the end(s) of a gangway....
-
T303.3 Cross Section
Gripping surfaces shall have a cross section complying with T303.3....
-
M302.3 Supports
Transfer supports, armrests, and reclining surfaces shall comply with M302.3....
