Secure mounting plate to wall surface at specified location with proper anchors (snugly) until proper centerline dimension is achieved....
Search Results "Minimum Dimension"
Filters
Commonly Searched Documents
-
AJW Architectural Products UG20-A Series UG20-A12 12" Concealed Set Screw Flange, 1.25" Diameter Grab Bar - Configuration A
-
Atlantis Railing
Note: Railing heights are offered in these dimensions due to nationwide building codes. However, Atlantis Rail can supply custom heights/lengths upon request....
-
Salsbury Industries Designer Wood Locker Single Tier 1 Wide
lift up handle and recessed hasp for added security Salsbury Industries is an ISO 9001: 2008 certified company and has excelled in the field of manufacturing since 1936 Compartment Dimensions...
-
Salsbury Industries Designer Wood Locker Single Tier 3 Wide
lift up handle and recessed hasp for added security Salsbury Industries is an ISO 9001: 2008 certified company and has excelled in the field of manufacturing since 1936 Compartment Dimension...
-
Door King Inc. 1150 Overhead Gate and Door opener
Dimensions: 21"W x 10.5"H x 149"- 221"L (Length depends on rail assembly ordered)....
-
Healthcraft Invisia ADA Serenaseat™ Folding Shower Seat
Product shall comply with ADA Guidelines, specifically the dimensions and structural strength of the shower seat. ...
-
Stanley Access Technologies Dura-Care 7200 Manual Sliding Door
Available TYPICAL WIDTH: 2-Panel | OPTION: 84" TO 108"; Clear Door Opening: 2-Panel (Standard) 35 1/4" to 47 1/4" HEADER SIZE: 4" BREAKOUT: Sliding Panel Breakout, Any Position JAMB DIMENSION...
-
General Comments (Preamble, Section-by-Section Analysis)
Many of these objections have been lodged on the basis that ADAAG exceeds the statutory mandate to establish ‘‘minimum’’ guidelines....
-
M301.2.1 Transfer Surface Height
Rationale: For many types of imaging equipment it will not be feasible to provide a transfer surface meeting the considered minimum height whether it is 17, 18, or 19 inches....
-
General Comments (Section-By-Section Analysis and Response to Comments)
Many of these objections have been lodged on the basis that ADAAG exceeds the statutory mandate to establish "minimum'' guidelines....
-
Accessible Entrance
Landing extends 18" minimum beyond the edge of door and 60" minimum out from door. New landing and ramp eliminates step at entrance....
-
Fire Rings, Grills, Fireplaces, and Wood Stoves
This space may be reduced to 36 inches (915 millimeters) minimum where a condition for exception exists....
-
3. Statutory and Regulatory Background
We are required by section 502 of the Rehabilitation Act to establish and maintain minimum guidelines and requirements for the accessibility standards adopted the federal agencies....
-
1011.2.1 Size and Location
Outdoor Constructed Feature Minimum Size and Location Picnic tables 36 inches (915 mm) on all usable sides of the table measured from...
-
Volume Control
Some commenters specifically recommended a minimum 25 decibels or greater....
-
1011.2.1 Size and Location
Table 1011.2.1 Clear Ground Space Outdoor Constructed Feature Minimum Size and Location Picnic tables 36 inches (915 mm) on all usable sides of...
-
III 3.11000 Insurance
ILLUSTRATION: An amusement park requires individuals to meet a minimum height requirement that excludes some individuals with disabilities for certain rides because of a limitation in its...
-
805 Medical Care and Long-Term Care Facilities
Beds can overlap turning space up to six inches where adequate toe clearance (9 inches high minimum) is provided....
-
Volume Control on Public Phones
The proposed rule specified a minimum of 25%, but many urged that all public phones should have volume control. Response....
-
Diagonal Curb Ramps
These curb ramps must have a 48 inch minimum clear space at the bottom....
-
404.2.4.1 Swinging Doors and Gates
Table 404.2.4.1 Maneuvering Clearances at Manual Swinging Doors and Gates Type of Use Minimum Maneuvering Clearance Approach Direction Door or Gate Side...
-
1136A.1 Receptacle heights
Baseboard electrical outlets used in relocatable partitions, window walls or other electrical convenience floor outlets are not subject to the minimum height requirements. 4. ...
-
11B-404.2.10 Door and gate surfaces
Tempered glass doors without stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch...
-
Visual Characters
For consistency with specifications for elevators in section 407, the Board has added an exception noting that the 40 inch minimum does not apply to visual characters indicating elevator...
