There is no standard format for this documentation; each unit may develop its own format to meet its specific needs....
Search Results "Electroacoustic Performance Standards"
Filters
Commonly Searched Documents
-
7.2 General Exceptions
-
4.1.7(3)(e)
NOTE: The technical provisions of sections 4.2 through 4.35 are the same as those of the American National Standard Institute’s document A117.1‒1980, except as noted in the text....
-
Question 2
The Access Board is expected to promulgate design standards for medical and dental diagnostic tables and chairs....
-
Protruding Objects [4.31.4]
Protruding Objects [4.31.4] Wall- or post-mounted pay phones and enclosures, due to their location above the standard sweep of canes (i.e., 27 inches high from the floor), can be a hazard...
-
68.79. Contract Providers
effective February 1, 2005, 30 TexReg 382) In addition to the specific terms of their contracts, contract providers are subject to the same minimum qualifications, responsibilities, and standards...
-
§ 37.165(b)(1)
(1) With respect to wheelchair/occupant combinations that are larger or heavier than those to which the design standards for vehicles and equipment of 49 CFR part 38 refer, the entity must...
-
12) Bathrooms
Generally only one stall must be accessible (standard five-by-five feet)....
-
11B-404.2.5 Thresholds
[2010 ADA Standards] EXCEPTION: Existing or altered thresholds ¾ inch (19 mm) high maximum that have a beveled edge on each side with a slope not steeper than 1:2 shall not be required...
-
11B-605.4 Flush controls
[2010 ADA Standards] 605.4 Flush Controls. Flush controls shall be hand operated or automatic. Hand operated flush controls shall comply with 309....
-
11B-903.3 Size
[2010 ADA Standards] 903.3 Size. Benches shall have seats that are 42 inches (1065 mm) long minimum and 20 inches (510 mm) deep minimum and 24 inches (610 mm) deep maximum....
-
11B-604.8.1.2 Doors
[2010 ADA Standards] 604.8.1.2 Doors....
-
410.1 General
Platform lifts shall comply with ASME A18.1 (1999 edition or 2003 edition) (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
F203.2 Existing Elements
Elements in compliance with an earlier standard issued pursuant to the Architectural Barriers Act or Section 504 of the Rehabilitation Act of 1973, as amended, shall not be required to comply...
-
Curb Ramps at Marked Crossings and Vehicular Lanes
In the final rule, requirements for the general location of curb ramps that were provided at [DOT ADA Standards] section 406.8 in the proposed rule have been integrated into this provision...
-
Scoping Requirements for Elevators
Scoping requirements for elevators in section 206.6 reference technical criteria for standard passenger elevators, destination-oriented elevators, existing elevators that are altered, limited-use...
-
Braille Specifications
A similar clarification has been included in the new ANSI A117.1 standard....
-
224.6 Housing at a Place of Education
For the purposes of the application of this section, the term "sleeping room" is intended to be used interchangeably with the term "guest room" as it is used in the transient lodging standards...
-
307 Protruding Objects
Objects mounted on walls above the standard sweep of canes (i.e., higher than 27 inches from the floor) and below the standard head room clearance (80 inches), are limited to a 4 inch depth...
-
410.1 General
Platform lifts shall comply with ASME A18.1 (1999 edition or 2003 edition) (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
6. Transfer Surface Height
As such every inch is significant both for designing tables that can go low enough to meet the new standard and in design of accessories or room siting as alternate means to attempt to meet...
-
410.1 General
Platform lifts shall comply with ASME A18.1 (1999 edition or 2003 edition) (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
206.2.4 Spaces and Elements
Florida requirements may be waived down to the ADA Standards requirements....
-
C.1. - Who within the agency is responsible for ensuring EIT purchases comply with Section 508?
Acquisition of EIT that meets the applicable technical provisions of the Access Board’s standards is the shared responsibility of requiring activity officials and contracting officials....