1.1.11 Ramp running slope....
Search Results "Cross Slope"
2010 ADA Definition
Cross Slope: The slope that is perpendicular to the direction of travel (see running slope).
Filters
Commonly Searched Documents
-
1.1.11 Ramp running slope
-
7.4.3.1 Running Slope (Grade)
Trail running slope (grade) of up to 1:20 (5 percent) is permitted for any distance....
-
5.1.3 Slope
The slope of the surface of the clear floor or ground space inside the camp shelter shall not be steeper than 1:48 (2 percent) in all directions....
-
2.4.1 Running Slope (Grade)
The running slope (grade) of ORARs shall comply with all applicable provisions of this section. Table 2.4.1....
-
Running Slope [1016.7.1]
Running slope, also referred to as grade, is the lengthwise slope of an ORAR, parallel to the direction of travel....
-
11B-406.6 Islands
Raised islands in crossings shall be cut through level with the street or have curb ramps at both sides....
-
11B-1008.2.5.3.1 Handrail gripping surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
1008.2.5.3.1 Handrail Gripping Surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
1008.2.5.3.1 Handrail Gripping Surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
11B-1008.2.5.3.1 Handrail gripping surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
11B-1008.2.5.3.1 Handrail gripping surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
505.7.1 Circular Cross Section
505.7.1 Circular Cross Section. Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
Non-Circular Cross Section and Clearance (§505.5, §505.7)
Non-Circular Cross Section and Clearance (§505.5, §505.7)...
-
Floor and Ground Surfaces: ADA Standard Section 503.4
Section 503.4 covers the current ADA Standards for the floor and ground surfaces at passenger loading zones.
-
1008.2.5.3.1 Handrail Gripping Surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
Ramp Requirements [§405]
Ramp Requirements [§405]
-
Q6.) How important is the method of measurement in considering the tolerances allowable in finished construction?
For ramps and curb ramps, DOJ has issued two technical assistance documents that show how to measure slopes. ...
-
4.3.3 Slope
The slope of tent pads and tent platforms shall not exceed 1:48 (2 percent) in any direction. Exception. ...
-
Handrail Clearance and Cross Section [§505.5, §505.7]
Handrail Clearance and Cross Section [§505.5, §505.7] Surface requirements and clearances facilitate a power grip along the length of handrails....
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
3.1.3.2 Running Slope (Grade) of Driveways
The running slope of driveways shall be no more than 1:12 (8.33 percent) for no more than 50 feet (15 m). Exception 1....
-
Figure 609.2.2 Grab Bar Non-Circular Cross Section – Drawing from the U.S. Access Board
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1 1/4 inches (32 mm) minimum and 2 inches (51 mm) maximum....
