(4) Mitigating measures include, but are not limited to:...
Search Results "Unit of Measurement"
Filters
Commonly Searched Documents
-
§ 36.105(d)(4) Mitigating measures include
-
§ 35.108(d)(4) Mitigating measures include
(4) Mitigating measures include, but are not limited to:...
-
Measuring Techniques
Air Force investigators take arm reach measurements one step farther, in that they measure arm reach in three "zones."...
-
Compilation of Instruments and Measurement Methods for Surface Accessibility
Compilation of Instruments and Measurement Methods for Surface Accessibility During the course of this project the following information was developed as background information to assist...
-
Mitigating measures
When determining if a person has a disability, a school cannot consider the ameliorative effects of mitigating measures when determining how the impairment impacts the major life activities...
-
General: ADA Standard Section 502.1
Section 502.1 of the ADA Standards covers information in the current ADA Standards for accessible parking spaces.
-
3. Measuring Door Openings
Measuring Door Openings Special care is needed when measuring the clear opening of a doorway. To measure the clear opening of a standard hinged door, open the door to 90 degrees....
-
Suggestions by Jean Tessmer
a digital inclinometer mounted to measure 1 - foot increments....
-
1.1.8 Alternate measurement tools
1.1.8 Alternate measurement tools....
-
I. Required Survey Tools
The following tools will be required to allow you to accurately complete the ADA Checklist for New Lodging Facilities: A. 12' Stiff Metal Tape Measure B. 24" Long Builders' Level (Square...
-
Unified Facilities Guide Specifications
The straightedge is to be held in contact with the surface and moved ahead one - half of the length of the straightedge for each successive measurement....
-
Take Good Measurements
Take Good Measurements When in doubt write it down. It’s better to have too much information than not enough. ...
-
1.1.16 Alternate measurement tools
1.1.16 Alternate measurement tools....
-
Sloped Surfaces
It is usually described as: a ratio (e.g., 1:20, means one unit of vertical rise for each 20 units of horizontal length); or a percentage (e.g., 8.33% which equates to a ratio of...
-
11B-502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings....
-
Residential Dwelling Unit Primary Entrance: ADA Standard Section 809.5.5
Communication features shall be provided at the residential dwelling unit primary entrance complying with 809.5.5....
-
Residential Dwelling Unit Communication Systems: ADA Standard Section 708.4
Communications systems between a residential dwelling unit and a site, building, or floor entrance shall comply with 708.4....
-
2.2.2 Structural Anthropometry (i.e. Body and WhMD Dimensions)
The 3-D measurements required the measurement of reference points and planes, as well as the measurement of key body and WhMD points with respect to the environment....
-
12102(4)(E)(i)
(i) The determination of whether an impairment substantially limits a major life activity shall be made without regard to the ameliorative effects of mitigating measures such as—...
-
Initial Measures and Transfer Setup
Wheelchair measurements were completed without the person seated in their wheelchair. ...
-
§1630.2(j)(1)(vi)
(vi) The determination of whether an impairment substantially limits a major life activity shall be made without regard to the ameliorative effects of mitigating measures....
-
§ 36.105(d)(1)(viii)
(viii) The determination of whether an impairment substantially limits a major life activity shall be made without regard to the ameliorative effects of mitigating measures....
-
§ 35.108(d)(1)(viii)
(viii) The determination of whether an impairment substantially limits a major life activity shall be made without regard to the ameliorative effects of mitigating measures....
-
Construction Specification Institute
Construction Specification Institute While developing suggested tolerances for surface materials, the Construction Specifications Institute developed a suggested method for measuring ramp...