Search Results "Shower Seat"
-
4.26 HANDRAILS, GRAB BARS, AND TUB AND SHOWER SEATS
-
4.26 Handrails, Grab Bars, and Tub and Shower Seats
-
4.26.1* GENERAL
All handrails, grab bars, and tub and shower seats required to be accessible by 4.1, 4.8, or 4.9 shall comply with 4.26....
-
4.26.1* General
All handrails, grab bars, and tub and shower seats required to be accessible by 4.1, 4.8, 4.9, 4.16, 4.17, 4.20 or 4.21 shall comply with 4.26....
-
4.26.3 STRUCTURAL STRENGTH
The structural strength of grab bars, tub and shower seats, fasteners, and mounting devices shall meet the following specification: (1) Bending stress in a grab bar or seat induced by...
-
4.26.3 Structural Strength
The structural strength of grab bars, tub and shower seats, fasteners, and mounting devices shall meet the following specification:...
-
4.26.3(1)
(1) Bending stress in a grab bar or seat induced by the maximum bending moment from the application of 250 lbf (1112N) shall be less than the allowable stress for the material of the grab...
-
4.26.3(2)
(2) Shear stress induced in a grab bar or seat by the application of 250 lbf (1112N) shall be less than the allowable shear stress for the material of the grab bar or seat....
-
4.26.3(3)
(3) Shear force induced in a fastener or mounting device from the application of 250 lbf (1112N) shall be less than the allowable lateral load of either the fastener or mounting...
-
4.26.3(4)
(4) Tensile force induced in a fastener by a direct tension force of 250 lbf (1112N) plus the maximum moment from the application of 250 lbf (1112N) shall be less than the allowable...
-
Seat [4.21.3]
Seat [4.21.3] ADAAG specifies maximum seat dimensions. Minimum dimensions contained in the CABO-ANSI A117.1‒1992 standard are acceptable....
-
Controls [4.21.5]
Controls [4.21.5] Controls and shower units can be located on any wall but where a folding seat is provided they must be located to be within reach of a person on the seat....
-
4.34.5.5 SHOWERS
If a shower is provided, it shall have the following features:...
-
Bathroom Do’s and Dont’s
Use metal hinges to secure the toilet lid and seat. Metal hinges are stronger and safer than plastic hinges. Don’t. Do not use short shower benches....
-
608.4 Seats (Exception)
608.4 Seats (Exception) This section requires a folding or non-folding seat to be provided in transfer type shower compartments....
-
608.3.2 Standard Roll-In Type Shower Compartments
Where a seat is provided in standard roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall opposite the seat....
-
608.3.3 Alternate Roll-In Type Shower Compartments
In alternate roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall farthest from the compartment entry....
-
608.4 Seats
A folding or non-folding seat shall be provided in transfer type shower compartments....
-
608.5.2 Standard Roll-In Type Shower Compartments
Where a seat is provided, the controls, faucets, and shower spray unit shall be installed on the back wall adjacent to the seat wall and shall be located 27 inches (685 mm) maximum from...
-
608.5.3 Alternate Roll-In Type Shower Compartments
In alternate roll-in type shower compartments, the controls, faucets, and shower spray unit shall be located above the grab bar, but no higher than 48 inches (1220 mm) above the shower floor...
-
610.1 General
Seats in bathtubs and shower compartments shall comply with 610....
-
610.3 Shower Compartment Seats
Where a seat is provided in a standard roll-in shower compartment, it shall be a folding type, shall be installed on the side wall adjacent to the controls, and shall extend from the back...
-
610.3.1 Rectangular Seats
The rear edge of a rectangular seat shall be 2 1/2 inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall....
-
610.3.2 L-Shaped Seats
The rear edge of an L-shaped seat shall be 2 1/2 inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall....