In bus loading zones restricted to use by designated or specified public transportation vehicles, each bus bay, bus stop, or other area designated for lift or ramp deployment shall comply...
Search Results "Bus Ramp"
-
11B-209.2.2 Bus loading zones
-
11B-810.3 Bus shelters
Bus shelters shall provide a minimum clear floor or ground space complying with Section 11B-305 entirely within the shelter....
-
11B-810.3 Bus shelters
Bus shelters shall provide a minimum clear floor or ground space complying with Section 11B-305 entirely within the shelter....
-
T402 Ramps and Bridgeplates
[See subsections ...]
-
T204.2 Doorways with Lifts, Ramps or Bridgeplates
Doorways with lifts or ramps shall comply with T502.2....
-
T502.2 Doorways with Lifts, Ramps or Bridgeplates
The vertical clearance at doorways with lifts, ramps or bridgeplates shall comply with T502.2....
-
11B-247.1.2.4 Bus stops
Where detectable warnings are provided at bus stop boarding and alighting areas in compliance with Section 11B-810.2.3, detectable warnings shall comply with Sections 11B-705.1.1 and 11B...
-
11B-247.1.2.4 Bus stops
Where detectable warnings are provided at bus stop boarding and alighting areas in compliance with Section 11B-810.2.3, detectable warnings shall comply with Sections 11B-705.1.1 and 11B...
-
Figure 810.2.2 Dimensions of Bus Boarding and Alighting Areas – Drawing from the U.S. Access Board
-
11B-705.1.2.4 Bus stops
When detectable warnings are provided at bus stop boarding and alighting areas, the detectable warnings shall extend the full width of the boarding/alighting area and shall be 36 inches...
-
11B-705.1.2.4 Bus stops
When detectable warnings are provided at bus stop boarding and alighting areas, the detectable warnings shall extend the full width of the boarding/alighting area and shall be 36 inches...
-
11B-810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2438 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
11B-810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2438 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
T404.3 Ramps and Bridgeplates
platform is greater than 2 inches (51 mm) horizontally or 5/8 inch (16 mm) vertically when measured at 50 percent passenger load with the vehicle at rest, non-rail vehicles shall provide ramps...
-
§ 38.159(c) Vehicle ramp
(c) Vehicle ramp—...
-
E. Chapter 4: Boarding and Alighting
All technical provisions related to boarding and alighting—including level boarding bus systems and steps (which formerly appeared in Chapters 2 and 5 respectively in the proposed rule)—...
-
T205.1 General
Non-rail vehicles shall provide illumination complying with T503 at ramps, bridgeplates, doorways, and boarding and alighting areas....
-
T202 Accessible Means of Boarding and Alighting
Provision of accessible boarding and alighting may be accomplished through the use of ramps and bridgeplates, lifts, or level boarding and alighting systems that meet the technical requirements...
-
Connection: ADA Standard Section 810.2.3
Bus stop boarding and alighting areas shall be connected to streets, sidewalks, or pedestrian paths by an accessible route complying with 402....
-
T503.2 Ramps and Bridgeplates
When ramps or bridgeplates are deployed, the walking surface shall be lighted with 2 foot-candles (22 lux) minimum of illumination....
-
Landings: ADA Standard Section 405.7
Section 405.7 covers the current ADA Standards for ramp landings.
-
§ 38.159(c)(2) Ramp surface
(2) Ramp surface....
-
Dimensions: ADA Standard Section 810.2.2
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2440 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
Bus Stop Pads
Specifications in 810.2 for bus stops applied to "bus stop pads" in the proposed rule....
