Suggestion: If the threshold is not more than 3/4 inches high, add beveled surfaces to both sides of the threshold or replace with a new threshold that is no more than 1/2 inch high and...
Search Results "Loose Fill Surface"
Filters
Commonly Searched Documents
-
Temporary Solutions for Election Day: Accessible Entrance to Polling Place
-
Mounting Location and Height [4.30.6]
Where adequate wall space is not available on the latch-side, signs are to be placed on the nearest adjacent wall surface....
-
6.1 General
Beach access routes shall be permanent or removable surfaces....
-
III-4.4300 Standards to apply
In order to promote safety, a portable ramp should have railings and a firm, stable, nonslip surface. It should also be properly secured....
-
Conclusion
We perceive the world, in part, through pressure and movement of materials and surfaces against our skin, and we sense the instantaneous positions of our limbs as we move through, and take...
-
Dimensions for Adults and Children [§102]
address access for children to: drinking fountains (§602) water closets and toilet compartments (§604) lavatories and sinks (§606) and dining and work surfaces...
-
Identification [§216.5, §502.6]
ISA designations on the parking surface, even if required by a state or local government, cannot substitute for above-ground signs that remain visible at all times....
-
11B-406.5.3 Landings
The landing provides an area for users to exit the curb ramp and proceed along the walking surface at the top of the curb ramp....
-
11B-609.3 Spacing
Configuration) the space between the walls and the grab bar shall be 1½ inches (38 mm) minimum for a distance of 6 inches on either side of the inside corner between two adjacent wall surfaces...
-
2. Shared Use Paths
address access to sidewalks, streets, and other pedestrian facilities, provide requirements for pedestrian access routes, including specifications for route width, grade, cross slope, surfaces...
-
2. Shared Use Paths
address access to sidewalks, streets, and other pedestrian facilities, provide requirements for pedestrian access routes, including specifications for route width, grade, cross slope, surfaces...
-
11B-609.3 Spacing
Section 11B-609.9 the space between the walls and the grab bar shall be 1½ inches (38 mm) minimum for a distance of 6 inches on either side of the inside corner between two adjacent wall surfaces...
-
Bradley Chrome-Plated Die Cast Double Robe Hook 932
Bradley Chrome-Plated Die Cast Double Robe Hook Model 932 Surface-Mounted - Concealed Wall Plates Die Cast Zamac with Polished Chrome Finish Double Robe Hook...
-
Panda S.85 All Aluminum Slim Profile Lift and Slide System
Other options including frosted or tinted glass, argon or krypton fill, and SDLs or TDLs may also be integrated for a more custom look....
-
11B-604.5.2 Rear wall
The gripping surface of the grab bar must be available for the entire 36-inch length without interruption....
-
Gamco Semi-Recessed Towel Dispenser - TD-4F
Description Unit fabricated of type 304 stainless steel with exposed surfaces having a #4 satin-finish....
-
Bradley Diplomat Napkin Disposal 4A10
Diplomat Washroom Accessories designed with unique dual-curve geometry Diplomat Accessories Gallery Recess, semi-recess, surface or partition mounted options Accepts...
-
About This Tool Kit
They asked us to help fill their knowledge gap....
-
Robert Dupuy, IALD, LC. Problems and Solutions
It’s a bunch of forms that you fill out. And it’s all based on the fact that you’re an honest person and that you’re not fudging those forms to make it work....
-
AJW Architectural Products U410 Series 12 Gallon Waste Receptacle w/ 4" Extended Waste - Recessed
One piece construction without miters or welds with 1/4" returns to wall surface for maximum strength....
-
AJW Architectural Products U2324 Unidoor C-fold/Multifold Towel Dispenser - Recessed
Face trim is an integral part of body with a #4 satin finish and 1/4" returns to wall surface for rigidity. One piece construction without miters or welds....
-
Bradley Soap Dispenser With ABS Plastic Valve 6563
Tank Type Vertical Surface-Mounted ADA Compliant Product Materials BODY: 20 gauge stainless steel with exposed surfaces in architectural satin finish....
-
Landscape Forms Inc. Washington Square Bench Collection
for two- or three-seat units Intermediate arms are formed of 1-1/2” diameter steel tubing Mounting: Seats ship with black nylon glide inserted into each leg For concealed surface...
-
Wikk Industries Inc. Bollard With Push Plate PART#BPRT126SMFT32D (630)
Formed 304 Satin Stainless Steel US32D (630), Surface mount with concealed mounting base, 1 prep for INGRESS’R ® ADA switch (630), Welded Flat top....
