clearance of 24 inches (610 mm) minimum above the finish floor or ground shall be permitted at lavatories and sinks used primarily by children 6 through 12 years where the rim or counter surface...
Search Results "Gripping Surface"
Filters
Commonly Searched Documents
-
606.2 Clear Floor Space
-
Existing Trails [F247.2]
the trail; clearing the trail of encroaching brush or grasses; and removing rock slides Maintaining trail tread, such as filling ruts, reshaping a trail bed, repairing a trail surface...
-
Medical Diagnostic Equipment Accessibility Standards Sub-Committee Recommendations Weight Scales
Types Of Equipment To Which Technical Criteria Applies Seated in a wheelchair (M303) Wheelchair space, including orientation, width, depth, knee and toe clearance, and surface...
-
R209 Accessible Pedestrian Signals and Pedestrian Pushbuttons (Section-by-Section Analysis)
., audible tones and vibrotactile surfaces) to pedestrians who are blind or have low vision....
-
R410.6 Character Height
Table R410.6 Visual Character Height Height to Finish Surface from Baseline of Character Horizontal Viewing Distance Minimum Character Height 1.0 m (3.3...
-
"Other Power-Driven Mobility Device" (Section-by-Section Analysis)
designed for areas or conditions without defined pedestrian areas, such as off-road bike paths, roads (except where allowed by law or where a sidewalk is not provided), freeways, or natural surfaces...
-
606.2 Clear Floor Space
clearance of 24 inches (610 mm) minimum above the finish floor or ground shall be permitted at lavatories and sinks used primarily by children 6 through 12 years where the rim or counter surface...
-
Protruding Objects and Trails
such as signs that extend into the clear width area of a trail, resting interval, or passing space between 27 inches (685 millimeters) and 80 inches (2,030 millimeters) above the travel surface...
-
Trail Facilities
not accessible— must be designed to comply with the applicable provisions in FSORAG, except that slopes not steeper than 1:20 (5 percent) are allowed if necessary for drainage of unpaved surfaces...
-
1018.1 General
The technical requirements address connections (1018.2); surface (1018.3); clear width (1018.4); obstacles (1018.5); openings (1018.6); slopes, including running slope (1018.7.1) and cross...
-
Developing a plan based on priorities
In order to promote safety, a portable ramp should be properly secured; have railings; and a firm, stable, nonslip surface....
-
Waviness Index
The Waviness Index measures the bumps and dips in a floor surface as the average of deviations up or down from the mid - points of 2 - , 4 - , 6 - , 8 - , and 10 - foot chords....
-
Positioning Supports Considered
., length, height above the patient support surface, location) to ensure their effectiveness?...
-
Protruding Objects
Requirements: All objects that protrude from surfaces or posts and all overhanging objects in areas where people walk shall comply with the following requirements: Objects mounted...
-
11B-604.8.1.4 Toe clearance
Partition components at toe clearances shall be smooth without sharp edges or abrasive surfaces....
-
11B-604.8.1.4 Toe clearance
Partition components at toe clearances shall be smooth without sharp edges or abrasive surfaces....
-
11B-504.4.1 Contrasting stripe
Exception: The contrasting marking stripe is permitted to be omitted where tread surfaces are such that the location of each tread is readily apparent when viewed in descent....
-
Getting to the Water—Beach Access Routes
A beach access route is a continuous unobstructed path that crosses the surface of the beach and provides pedestrian access to the water....
-
Outdoor Constructed Features
The proposed rule based the size of the clear ground space at outdoor constructed features on the dimensions for clear floor or ground surfaces in 305.2 of the Architectural Barriers Act...
-
H. Barriers Affecting Accessibility and Usability of Medical Diagnostic Equipment
., height, width, length), contact surfaces (e.g., stiffness, comfort, color contrast), supports for transferring onto and off of equipment and positioning their bodies on the equipment...
-
Activar JL Industries Academy Series 1027V10 Aluminum Fire Extinguisher Cabinet
Surface-mount has a square edge. 1 3/4" face trim on frame and 1 1/4" trim on door. Tub: Constructed of cold rolled steel with white powder-coat finish standard....
-
Bobrick Recessed Sharp Disposal B-35016
Door — 22 gauge stainless steel with exposed surfaces in #4 satin finish. Heavy-duty stainless steel piano-hinge. Tumbler lock keyed like other Bobrick accessories....
-
DORMA 8600 Series Door Closer
Grade 1 Surface Applied Door Closers The 8600 door closer series is a non-handed surface applied door closer with adjustable spring power and backcheck positioning adjustment....
-
Willoughby Industries UW-1317-HEU Series Contoured High Efficiency Urinal
The construction shall be all-welded with exposed stainless steel surfaces polished to a satin finish. Contoured interior and exterior surfaces for ease of cleaning....
