Handrail gripping surfaces shall extend beyond and in the same direction of stair flights and ramp runs in accordance with Section 11B-505.10....
Search Results "Recreational Surfacing"
Filters
Commonly Searched Documents
-
11B-505.10 Handrail extensions
-
Track Crossing
The proposed rule required route surfaces to be level with the rail top, but permitted a 2 ½ inch gap at the inner edge of rails to accommodate wheel flanges (1003.2.7)....
-
What Are the Requirements for Accessible Routes?
This section describes the various features of accessible routes within a play area, including location, clear width, slope, and accessible surfaces. ...
-
403.5.1 Clear Width
Except as provided in 403.5.2 and 403.5.3, the clear width of walking surfaces shall be 36 inches (915 mm) minimum....
-
1018.5 Obstacles
EXCEPTION: Where the surface is other than asphalt, concrete, or boards, obstacles shall be permitted to not exceed 1 inch (25 mm) in height measured vertically to the highest point....
-
R406 Reach Ranges (Section-by-Section Analysis)
R406 Reach Ranges (Section-by-Section Analysis) Forward and side reach ranges must be between 380 millimeters (1.25 feet) and 1220 millimeters (4 feet) above the finish surface....
-
f-iv
[ADA Standards § 4.8.4] Yes No Note: The level landing may be part of the sidewalk or walking surface. Notes: 1. At least 36 inches between handrails 2....
-
12162(a)(4)(A)(ii)
(ii) appropriate auxiliary aids and services, including a hard surface on which to eat, shall be provided to ensure that other equivalent food service is available to individuals with disabilities...
-
Clear Tread Width of Trails
Clear tread width is the width of traveled surface between obstacles on the ground and above the ground (figure 129). Provide at least 36 inches (915 millimeters) of clear tread width....
-
2 Method
Systematic outdoor evaluations were performed on 13 different detectable warning colors/patterns on 4 different simulated sidewalk surfaces by 50 visually impaired participants who have...
-
1018.5 Obstacles
EXCEPTION: Where the surface is other than asphalt, concrete, or boards, obstacles shall be permitted to not exceed 1 inch (25 mm) in height measured vertically to the highest point....
-
1015.1 General
The technical requirements address the clear ground space (1015.2) and viewing space (1015.3) at distinct viewing locations; the turning space within viewing areas (1015.4); and the surface...
-
Protruding Object
constructed feature such as a sign that overhangs an ORAR, beach access route, trail, resting interval, or passing space between 27 inches (685 mm) and 80 inches (2030 mm) above the travel surface...
-
4.5.1 General
In alterations, where a condition for exception in section 1.1 prohibits full compliance with a specific requirement for clear floor or ground space surface, slope, size, or location, the...
-
11B-703.7.2.6.2 Women’s toilet and bathing facilities
The color of the circle symbol shall contrast with the color of the door or surface on which the circle symbol is mounted, either light on a dark background or dark on a light background...
-
Where do I measure for a handrail extension?
Phrase 3: SHALL NOT BE OBSTRUCTED ALONG THEIR TOPS OR SIDES: 505.6 Gripping surface....
-
Accessibility - Flatness and Lippage
Conformance to this standard requires that subfloor surfaces conform to the following: no variation greater than 1/4" in 10 feet, nor 1/16" in 1 ft. from the required plane....
-
A. ACCESSIBLE SEATING
Wheelchair Spaces shall be thirty six (36) inches wide (or as otherwise required by Section 802), located on a level floor surface, and shall adjoin accessible routes. ...
-
Fixed position maps and kiosks
While it is normally more convenient and practical to mount these maps on vertical surfaces, as is typical for publicly displayed maps, it is better to place tactile maps on a horizontal...
-
1002.6 Transfer Devices for Use with Amusement Rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
11B-1002.6 Transfer devices for use with amusement rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
1002.6 Transfer Devices for Use with Amusement Rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
When Ramps Are Required
Rise of a ramp is the amount of vertical distance the inclined or slanted surface ascends or descends....
-
R210.3 Shared Use Paths
Objects shall not overhang or protrude into any portion of a shared use path at or below 2.4 m (8.0 ft) measured from the finish surface....