457 mm) of the latch side at an interior doorway, or within 24 inches (610 mm) of the latch side of an exterior doorway, projects more than 8 inches (203 mm) beyond the face of the door, measured...
Search Results "Mitigating Measures"
-
11B-404.2.4.3 Recessed doors and gates
-
Seeger et al.
Both unoccupied and occupied dimensions of device width and length were measured as well as a set of other basic dimensions....
-
§ 382.37 Seat assignments
b) If a person’s disability results in involuntary active behavior that would result in the person properly being refused transportation under § 382.31, and the safety problem could be mitigated...
-
RESPONSE AND RECOVERY OPERATIONS
It serves as the forum where organizations share knowledge and resources throughout the disaster cycle - preparation, response, recovery and mitigation - to help disaster survivors and their...
-
11B-404.2.11 Vision lights
Under CBC, an existing primary entrance door with a noncompliant vision light is not Safe Harbored, unless the Exception at 11B-404.2.11 applies, and must be mitigated under path of travel...
-
11B-404.2.11 Vision lights
Under CBC, an existing primary entrance door with a noncompliant vision light is not Safe Harbored, unless the Exception at 11B-404.2.11 applies, and must be mitigated under path of travel...
-
1.2.7
1.2.7 When local variations (flatness) for cross slope of ramps are measured according to 1.1.14 at least 80% (rounded to the nearest whole number) should not exceed a 2% slope....
-
Character Height: ADA Standard Section 703.2.5
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
Original research for ANSI A117.1 (1957 - 1961)
1961, American National Standard Specifications for Making Buildings and Facilities Accessible to, and Usable by, the Physically Handicapped, ramps were assessed for flatness based on measuring...
-
3.3.5 Seat Height
The reference points used for measurement can yield quite different results for seat height....
-
APPENDIXES
X1.1.2 PRI precision depends on the interval between adjacent profile elevation measures....
-
C. Training
, including: (a) why such measures are necessary; (b) how the measures must be implemented (e.g., how to install ramps, the placement of mats over (and not in front of) thresholds); and...
-
III. Background
., 527 U.S. 471, 482 (1999), the Court ruled that whether an impairment substantially limits a major life activity is to be determined with reference to the ameliorative effects of mitigating...
-
3. Q: I know I can't give a job applicant a medical exam before a conditional job offer is made. But what about physical agility and physical fitness tests?
A: You can give job applicants tests measuring an applicant's ability to perform job-related tasks or physical fitness tests (tests measuring performance of running, lifting, etc.) before...
-
2013 & 2016 CBC Answer
X3 measurement has no code basis. Both X1 and X2 measurement are acceptable if minimum width of 108 inches are achieved....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2440 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
C. Training
, including: (a) why such measures are necessary; (b) how the measures must be implemented (e.g., how to install ramps, the placement of mats over (and not in front of) thresholds); and...
-
LRV Guru App - Demo #1
Just enter the LRV values if you know them -- or -- use a NODE+Chroma hand-held colorimeter to measure for LRV....
-
604.3.1 Size
Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular from the rear wall....
-
9. Precision and Bias
9.1 The precision and bias of the computed PRI is limited by the procedures used in making the longitudinal profile measurement. 9.2 For the effects of the precision and bias of the measured...
-
604.3.1 Size
Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular from the rear wall....
-
§ 382.51 Communicable diseases
and severity of the risk; that the potential harm to the health and safety of others will actually occur; and whether reasonable modifications of policies, practices, or procedures will mitigate...
