The pictured example vanity using the stock bracket and dimensions shown in section view may not provide the required minimum 8" deep knee clearance at 27" AFF under the vanity top (306)...
Search Results "Adult Dimension"
-
Design Opportunity
-
Chapter 1: Application and Administration
Chapter 1: Application and Administration This chapter states general principles that recognize the purpose of the guidelines (101), provisions for adults and children (102), equivalent...
-
11B-302.3 Openings
Elongated openings shall be placed so that the long dimension is perpendicular to the dominant direction of travel. Advisory 11B-302.3 Openings....
-
M305.2.4 Cross Section (Section-by-Section Analysis)
of 2 inches maximum, and a perimeter dimension of 4 inches minimum and 4.8 inches maximum....
-
Number of Accessible Guest Rooms
In 1999, 2.3 percent of households had an adult member who uses a wheelchair; and by 2010, it is projected that 4 percent of households will have an adult member who uses a wheelchair....
-
5.4.6 Transfer Support Gripping Surface Cross Section and Clearances for M301, M302, and M305.2
Grab bars with non-circular cross sections must have a cross section dimension of 2 inches maximum and a perimeter dimension of 4 inches minimum and 4.8 inches maximum....
-
Job Training Partnership Act of 1982
_______________________________________________________ 10/13/1982 The Job Training Partnership Act of 1982 establishes federal assistance programs to prepare youth and unskilled adults...
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
§ 36.311(b)(2)(i)
(i) The type, size, weight, dimensions, and speed of the device;...
-
§ 35.137(b)(2)(i)
(i) The type, size, weight, dimensions, and speed of the device;...
-
Transfer Surface Size: Equipment Used by Patients in Supine, Prone, or Side-Lying Position (M301.2.2)
The transfer surface dimensions do not include headrests, footrests, or similar supports for body extremities that do not support the patient’s overall body position....
-
Knee & Toe Space [M303.2.4]
Rationale The issue of Clearance and Unobstructed Floor Space The knee and toe clearance dimensions, as well as the unobstructed floor space dimensions, dictate how close a patient...
-
407.4.6.2.1 Size
Buttons shall be ¾ inch (19 mm) minimum in their smallest dimension....
-
4.3.3 Clear Floor Area
The 95th percentile dimension values for occupied length and breadth provide a reasonable threshold value for determining the dimensions for clear floor area length and breadth....
-
608.2.2 Standard Roll-In Type Shower Compartments
Standard roll-in type shower compartments shall be 30 inches (760 mm) wide minimum by 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
Section 4.26.2
Handrail gripping surfaces with a non-circular cross section must have a perimeter dimension of 4 inches to 6 ¼ inches, and a cross section dimension of 2 ¼ inches maximum....
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
R103 Conventions (Section-by-Section Analysis)
R103 Conventions (Section-by-Section Analysis) Conventional industry tolerances apply where dimensions are not stated as a range....
-
11B-409.4.6.1 Size
Control buttons shall be ¾ inch (19.1 mm) minimum in their smallest dimension....
-
§ 36.311(c)(1)
(1) The dimensions, weight, and operating speed of the mobility device in relation to a wheelchair;...
-
§ 35.137(c)(1)
(1) The dimensions, weight, and operating speed of the mobility device in relation to a wheelchair;...
-
3.2 Dimensional Tolerances
All dimensions are subject to conventional building industry tolerances for field conditions....