The shower spray unit shall have an on/off control with a non-positive shut-off....
Search Results "Shall"
Filters
Commonly Searched Documents
-
608.6 Shower Spray Unit and Water
-
11B-602.6 Water flow
The spout shall provide a flow of water 4 inches (102 mm) high minimum and shall be located 5 inches (127 mm) maximum from the front of the unit....
-
11B-602.6 Water flow
The spout shall provide a flow of water 4 inches (102 mm) high minimum and shall be located 5 inches (127 mm) maximum from the front of the unit....
-
11B-608.5.2 Standard roll-in type shower compartments
In standard roll-in type shower compartments, the controls, faucets, and the shower spray unit shall be located on the back wall of the compartment adjacent to the seat 16 inches (406 mm...
-
11B-221.2.1.6 Specialty seating areas
In assembly areas, wheelchair spaces shall be provided in each specialty seating area that provides spectators with distinct services or amenities that generally are not available to other...
-
11B-221.2.1.6 Specialty seating areas
In assembly areas, wheelchair spaces shall be provided in each specialty seating area that provides spectators with distinct services or amenities that generally are not available to other...
-
11B-221.2.1.6 Specialty seating areas
In assembly areas, wheelchair spaces shall be provided in each specialty seating area that provides spectators with distinct services or amenities that generally are not available to other...
-
11B-810.4 Bus signs
Bus route identification signs shall comply with Sections 11B-703.5.1 _|Finish and Contrast|_ through 11B-703.5.4 _|Character Proportions|_, and Sections 11B-703.5.7 _|Stroke Thickness|_...
-
11B-242.4 Spas
At least one accessible means of entry shall be provided for spas....
-
232.5.1 Cubicles and Counters
At least 5 percent, but no fewer than one, of cubicles shall comply with 902 on both the visitor and detainee sides....
-
1134A.8, Item 1
Vanities and lavatories shall be installed with the centerline of the fixture a minimum of 18 inches (457 mm) horizontally from an adjoining wall or fixture to allow for forward approach...
-
M302.2.5 Unobstructed Transfer
Each transfer side complying with M302.2.4 shall provide unobstructed access to transfer surfaces. EXCEPTIONS: 1....
-
1007.8.1 System requirements
Two-way communication systems shall provide communication between each required location and a central control point location approved by the fire department....
-
1009.2.1 Pool Lift Location
Pool lifts shall be located where the water level does not exceed 48 inches (1220 mm). EXCEPTIONS: 1....
-
406.8 Detectable Warnings
A curb ramp shall have a detectable warning complying with 705....
-
F228.1 General
Where provided, at least one of each type of depository, vending machine, change machine, and fuel dispenser shall comply with 309. EXCEPTIONS: 1....
-
608.2.1 Transfer Type Shower Compartments
Transfer type shower compartments shall be 36 inches (915 mm) by 36 inches (915 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (915...
-
405.8 Handrails
Ramp runs with a rise greater than 6 inches (150 mm) shall have handrails complying with 505....
-
1009.2.1 Pool Lift Location
Pool lifts shall be located where the water level does not exceed 48 inches (1220 mm). EXCEPTIONS: 1....
-
405.8 Handrails
Ramp runs with a rise greater than 6 inches (150 mm) shall have handrails complying with 505....
-
1009.5.2 Transfer Space
A transfer space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer platform surface and shall...
-
4.1.2(5)(b)
(b) One in every eight accessible spaces, but not less than one, shall be served by an access aisle 96 in (2440 mm) wide minimum and shall be designated “van accessible” as required by 4.6.4...
-
4.8.2* SLOPE AND RISE
The least possible slope shall be used for any ramp. The maximum slope of a ramp in new construction shall be 1:12. The maximum rise for any run shall be 30 in (760 mm) (see Fig. 16)....
-
4.10.12(3)
All floor buttons shall be no higher than 48 in (1220 mm), unless there is a substantial increase in cost, in which case the maximum mounting height may be increased to 54 in (1370 mm),...