Information on specific tolerances may be available from industry or trade organizations, code groups and building officials, and published references. ...
Search Results "ISO: International Organization for Standardization"
Filters
Commonly Searched Documents
-
11B-104.1.1 Construction and manufacturing tolerances
-
Program requirements. (Section-by-Section Analysis)
One organization supported a requirement to modify additional cells when the existing number of accessible cells is inadequate....
-
405 Ramps
Commenters urged that this exception be removed for consistency with the ANSI A117.1‒1998 standard and the International Building Code (IBC). Response....
-
1630.16(b)(5)
(5) May require that its employees employed in an industry subject to such regulations comply with the standards established in the regulations (if any) of the Departments of Defense and...
-
Check-Out Aisles and Sales and Service Counters
Section 227 of the 2010 Standards clarifies the requirements for food service lines....
-
Enforcing Authority
An agency or other governmental entity that adopts the MDE Standards as mandatory requirements for entities subject to its jurisdiction....
-
Hospital Patient Toilet Rooms
An exception was added in section 223.1 of the 2010 Standards to allow toilet rooms that are part of critical or intensive care patient sleeping rooms to no longer be required to provide...
-
Is Prior Knowledge of the Circulation Path Location(s) Necessary?
Once properly notified by appropriate visual notification devices of an alarm or special instructions, people who are deaf or hard of hearing can use any standard means of egress from the...
-
Sec. 469.003(b)
(b) To the extent there is not a conflict with federal law and it is not beyond the state's regulatory power, the standards adopted under this chapter apply to a building or facility constructed...
-
"Disco" Elevator
See Standards §§ 4.10.5, 4.10.14....
-
Subpart D-New Construction and Alterations (Section-by-Section Analysis)
The Department is proposing to amend this subpart to adopt the proposed standards and to make related changes to give effect to these changes, as described below....
-
E2-b
[ADA Standards § 4.4.2] Yes No...
-
D.2. - Must requiring officials consider all the Access Board’s technical provisions and functional performance criteria each time they purchase EIT?
Requiring officials need only consider all applicable technical provisions from the Access Board’s standards to ensure acquired products provide comparable access (see section B.2.ii, above...
-
B7-b
[ADA Standards § 4.7.2] Yes No Note: 1:12 is one inch of vertical height for each 12 inches of length....
-
§ 36.406(f) Assembly areas
Assembly areas subject to this section shall comply with the provisions of the 2010 Standards applicable to assembly areas, including, but not limited to, sections 221 and 802....
-
12201(e) Benefits under State worker's compensation laws
—Nothing in this Act alters the standards for determining eligibility for benefits under State worker’s compensation laws or under State and Federal disability benefit programs....
-
1008.2.6.2 Use Zones
Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition) (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
§100.60(b)(6)
(6) Conditioning the availability of a dwelling, including the price, qualification criteria, or standards or procedures for securing the dwelling, on a person's response to harassment because...
-
§1630.16(b)(5)
(5) May require that its employees employed in an industry subject to such regulations comply with the standards established in the regulations (if any) of the Departments of Defense and...
-
Transportation Facilities
The ADA also establishes standards for transportation vehicles, including buses, vans, and rail cars (which are not discussed in this guide)....
-
Elevator Car Requirements [§407.4]
Elevator Car Requirements [§407.4] The ADA Standards specify the minimum car dimensions....
-
When door vision lights are limited to 100 square inches by the fire code, is compliance with the specified maximum height of 43” to the bottom edge still required?
The Standards do not exempt such doors from the requirement for vision lights (§404.2.11)....
-
§ 35.151(g) Assembly areas.
Assembly areas subject to this section shall comply with the provisions of the 2010 Standards applicable to assembly areas, including, but not limited to, sections 221 and 802....
-
TEXT TELEPHONE
Machinery or equipment that employs interactive text-based communications through the transmission of coded signals across the standard telephone network....