Side Approach Side reach depth is important to consider in the design and location of sinks....
Search Results "Side Transfer"
Filters
Commonly Searched Documents
-
Side Approach
-
Side Approach
Side Approach Where space is provided for a side approach, controls can be mounted at the heights allowed for side reaches....
-
Grab Bar and Backrest Evaluation
The grab bars were frequently used as handhelds during the transfer process and for one person it made the difference of being able to do a non-level transfer to the platform....
-
Entry Points and Seats: ADA Standard Section 1008.4.4
Where play components require transfer to entry points or seats, the entry points or seats shall be 11 inches (280 mm) minimum and 24 inches (610 mm) maximum from the clear floor or ground...
-
Ticket transfer. (Section-by-Section Analysis)
Ticket transfer. The Department received many comments asking whether accessible seating has the same transfer rights as general seats....
-
5.2.1 Transfer Surface Size
5.2.1 Transfer Surface Size...
-
19 Inch Low Height
transfer surface....
-
5.4.9 Interruptions Along Transfer Support Gripping for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.9 Interruptions Along Transfer Support Gripping for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
11B-1008.4.4 Entry points and seats
Where play components require transfer to entry points or seats, the entry points or seats shall be 11 inches (279 mm) minimum and 24 inches (610 mm) maximum from the clear floor or ground...
-
Side Entry Openings, and Width and Length of Wheelchair Space
Side Entry Openings, and Width and Length of Wheelchair Space If the wheelchair space can only be entered from the side, the ride must be designed to permit sufficient turning space for...
-
M301.2.1 Adjustability
Transfer surfaces shall be adjustable in height measured from the floor to the top of the uncompressed transfer surface and shall provide the following: A....
-
M302.3.1 Transfer Supports
Transfer supports shall be provided for use with the transfer sides required by M302.2.3 and shall comply with M305.2....
-
604.5.1 Side Wall
604.5.1 Side Wall....
-
Transfer Surface Size: Equipment Used by Patients in a Seated Position (M302.2.2)
, or side-lying position....
-
M302.3.1 Transfer Supports
Transfer supports shall be provided for use with transfer sides required by M302.2.4 and shall comply with M305.2.1.1, M305.2.2.1, and M305.2.3 through M305.2.8....
-
H4
On the pull side of the door, is there at least 18 inches clearance provided on the latch side if the door is not automatic or power-operated?...
-
18 Inch Low Height
could be a reasonable compromise since the group most affected by increasing the height would be manual wheelchair users who could accommodate a 1 inch change in vertical clearance during transfer...
-
Side Approach and Reach
[See subsections ...]
-
g-iii
Is there clear maneuvering floor space in front of each accessible door (see ADA Standards § Fig. 25) and, on the pull side, is there at least 18 inches clear floor space beyond the latch...
-
5.4.7 Transfer Support Gripping Surface Clearance for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.7 Transfer Support Gripping Surface Clearance for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
604.5.1 Side Wall
The side wall grab bar shall be 42 inches (1065 mm) long minimum, located 12 inches (305 mm) maximum from the rear wall and extending 54 inches (1370 mm) minimum from the rear wall. ...
-
M301.2.2 Sunset Provision (Section-by-Section Analysis)
(Significant Changes – Transfer Surface Adjustability), this is a new provision that was added to the final rule in conjunction with the new requirement of a low height range in M301.2.1...
-
5.2.1 Transfer Surface Size Recommendations for M301
5.2.1 Transfer Surface Size Recommendations for M301 Description: The transfer surface is the part of the diagnostic equipment onto which patients who use mobility devices or aids transfer...
-
407.12.2.2 Obstructed Side Reach (Section-by-Section Analysis)
407.12.2.2 Obstructed Side Reach (Section-by-Section Analysis) This section proposes that, where the operable part is located more than 10 inches, but not more than 24 inches, behind...