(1) Design load. Ramps 30 inches (760 mm) or longer shall support a load of 600 pounds (2665 N), placed at the centroid of the ramp distributed over an area of 26 inches by 26 inches...
Search Results "Road Surface Treatment"
-
§ 38.159(c)(1) Design load
-
§ 38.159(b)(12) Use by standees
(12) Use by standees. Lifts shall accommodate persons using walkers, crutches, canes or braces or who otherwise have difficulty using steps. The platform may be marked to indicate a...
-
§ 38.159(b)(1) Design load
(1) Design load. The design load of the lift shall be at least 600 pounds (2665 N). Working parts, such as cables, pulleys, and shafts, which can be expected to wear, and upon which...
-
13. Do the provisions for openings in floor and ground surfaces in Section 302.3 apply to walking surfaces in play areas?
Do the provisions for openings in floor and ground surfaces in Section 302.3 apply to walking surfaces in play areas? Yes....
-
Vertical Surface Discontinuities
Vertical Surface Discontinuities. Vertical differences in level between two adjacent surfaces....
-
407.4.2 Floor Surfaces
407.4.2 Floor Surfaces. Floor surfaces in elevator cars shall comply with 302 and 303....
-
404.2.4.4 Floor or Ground Surface
Floor or ground surface within required maneuvering clearances shall comply with 302. Changes in level are not permitted. EXCEPTIONS: 1....
-
404.2.4.4 Floor or Ground Surface
Floor or ground surface within required maneuvering clearances shall comply with 302. Changes in level are not permitted. EXCEPTIONS: 1....
-
11B-809.9.4 Work surfaces
Work surfaces shall be 36 inches (914 mm) maximum above the finish floor with minimum lengths at the following locations as required by this section: Linear length of 30 inches...
-
11B-809.9.4 Work surfaces
Work surfaces shall be 36 inches (914 mm) maximum above the finish floor with minimum lengths at the following locations as required by this section: Linear length of 30 inches...
-
5.2.1.2 Transfer Surface Depth Recommendation for M301
5.2.1.2 Transfer Surface Depth Recommendation for M301 The Committee recommends a minimum transfer surface depth of 17 inches for all M301 except imaging equipment....
-
KICK PLATE
An abrasion-resistant plate affixed to the bottom portion of a door to prevent a trap condition and protect its surface. Advisory Definition of KICK PLATE....
-
KICK PLATE
An abrasion-resistant plate affixed to the bottom portion of a door to prevent a trap condition and protect its surface. Advisory Definition of KICK PLATE....
-
Accessible Exterior Surfaces
Accessible Exterior Surfaces This is an executive summary of the “Accessible Exterior Surfaces Technical Report” dated 24 April 1999....
-
4.10.10 Floor Surfaces
Floor surfaces shall comply with 4.5....
-
4.10.10 FLOOR SURFACES
Floor surfaces shall comply with 4.5....
-
DEL Motorized Solutions Remote Control Cellular Shades
This system is ideal for projects with smaller sized treatments. Comfort Control Systems Our Comfort Control Systems are in one word, quieter....
-
407.4.2 Floor Surfaces
Floor surfaces in elevator cars shall comply with 302 and 303....
-
407.4.2 Floor Surfaces
Floor surfaces in elevator cars shall comply with 302 and 303....
-
4.1.2 Surface Design of Examination Tables and Chairs
4.1.2 Surface Design of Examination Tables and Chairs For several reasons including patient comfort and safety, the surfaces of many examination tables and chairs are not flat....
-
Other Features in Progress
Shades in the DR to reduce contrast glare Attached area rugs in the den and DR Moveable cabinets. Moveable stairs for transfer into the spa from a...
-
General: ADA Standard Section 403.1
Section 403.1 of the ADA Standards covers information in the current ADA Standards for walking surfaces that are part of an accessible route.
-
§ 38.159(b)(8) Platform entrance ramp
ramp, shall not exceed a slope of 1:8, measured on level ground, for a maximum rise of 3 inches (75 mm), and the transition from roadway or sidewalk to ramp may be vertical without edge treatment...
-
High work surface
All of the seating spaces/work surfaces were approximately 42" high....
