Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (100 mm) minimum and 6 1/4 inches (160 mm) maximum, and a cross-section dimension...
Search Results "Handrail Continuity"
Filters
Commonly Searched Documents
-
505.7.2 Non-Circular Cross Sections
-
Clearances between a handrail and wall surface: 2012 NFPA 101 vs. 2010 ADA
Question/Issue: According to the new 2012 NFPA 101 Life Safety Code, Chapter 7, Section 7.2.2.4.4.5 & Exhibit 7.97, the finger clearance at an existing stair handrail should be...
-
Figure 505.6 Horizontal Projections Below Gripping Surface – Drawing from the U.S. Access Board
-
Sections 4.8.5 and 4.9.4
• Sections 4.8.5 and 4.9.4 of the 1991 Standards require handrail gripping surfaces to be continuous, and to be uninterrupted by newel posts, other construction elements, or obstructions...
-
Can stair handrail extensions overlap door maneuvering clearances?
No, handrails and other elements cannot overlap door maneuvering clearances....
-
§ 38.77(b)
(b) At entrances equipped with steps, handrails and stanchions shall be provided in the entrance to the vehicle in a configuration which allows passengers to grasp such assists from outside...
-
T207.1 General
Non-rail vehicles shall provide handrails, stanchions, and handholds in accordance with T207. Handrails, stanchions, and handholds shall comply with T303....
-
Section 4.26.4
• Section 4.26.4 of the 1991 Standards requires handrail gripping surfaces to have edges with a minimum radius of 1/8 inch....
-
Can handrails overlap door maneuvering clearances?
door maneuvering clearances can be offset up to 8” from the face of the door or gate to accommodate wall thickness, casework, shelves, or other elements adjacent to doorways, including handrails...
-
T303.4 Clearance
Clearance between gripping surfaces and adjacent surfaces shall be 1½ inches (38 mm) minimum.
-
Ramps
Provide handrails on each side of the ramps at the following locations:...
-
Non-Circular Cross Section and Clearance (§505.5, §505.7)
Non-Circular Cross Section and Clearance (§505.5, §505.7)
-
Extremely well done!
Hello Corada, Thank you ETA and Dan for pointing me to this How-to video on measuring handrail extensions....
-
A4.26.1 General
Many disabled people rely heavily upon grab bars and handrails to maintain balance and prevent serious falls....
-
A4.26.1 GENERAL
Many disabled people rely heavily upon grab bars and handrails to maintain balance and prevent serious falls....
-
4.9.4(3)
(3) The clear space between handrails and wall shall be 1‒1/2 in (38 mm)....
-
T207.3 Fare Collection Devices
Handrails shall be provided at fare collection devices and shall be configured so that they can be used for support when at the fare collection device....
-
R409.8 Surfaces
Handrail gripping surfaces and any surfaces adjacent to them shall be free of sharp or abrasive elements and shall have rounded edges....
-
R302.3.2 Shared Use Paths
R302.3.2 Shared Use Paths. A pedestrian access route shall be provided for the full width of a shared use path. As proposed in the NPRM, R302.3 would require pedestrian access...
-
604.9.6 Dispensers
Dispensers shall not be of a type that controls delivery or that does not allow continuous paper flow....
-
604.9.6 Dispensers
Dispensers shall not be of a type that controls delivery or that does not allow continuous paper flow....
-
604.9.6 Dispensers
Dispensers shall not be of a type that controls delivery or that does not allow continuous paper flow....
-
11B-604.9.6 Dispensers
Dispensers shall not be of a type that controls delivery or that does not allow continuous paper flow....
