Handrails and stanchions with a non-circular cross section shall have a perimeter dimension of 4 inches (100 mm) minimum and 6¼ inches (160 mm) maximum, and a cross section dimension of...
Search Results "Handrail Continuity"
Filters
Commonly Searched Documents
-
T303.3.3 Handrail and Stanchion Non-Circular Cross Section
-
505.7 Cross Section
Handrail gripping surfaces shall have a cross section complying with 505.7.1 or 505.7.2....
-
505.7 Cross Section
Handrail gripping surfaces shall have a cross section complying with 505.7.1 or 505.7.2....
-
505.7 Cross Section
Handrail gripping surfaces shall have a cross section complying with 505.7.1 or 505.7.2....
-
11B-505.7 Cross section
Handrail gripping surfaces shall have a cross section complying with Section 11B-505.7.1 or 11B-505.7.2....
-
505.7 Cross Section
Handrail gripping surfaces shall have a cross section complying with 505.7.1 or 505.7.2....
-
11B-505.7 Cross section
Handrail gripping surfaces shall have a cross section complying with Section 11B-505.7.1 or 11B-505.7.2....
-
11B-505.7 Cross section
Handrail gripping surfaces shall have a cross section complying with Section 11B-505.7.1 or 11B-505.7.2....
-
1011.11 Handrails
... [DSA-AC] For applications listed in Section 1.9.1 regulated by the Division of the State Architect-Access Compliance, see Chapter 11B, Sections 11B-504.6 and 11B-505.
-
1011.11 Handrails
... [DSA-AC] For applications listed in Section 1.9.1 regulated by the Division of the State Architect-Access Compliance, see Chapter 11B, Sections 11B-504.6 and 11B-505.
-
d-iv
Are the handrails mounted 34 to 38 inches above the ramp surface? [ADA Standards § 4.8.5] Yes No...
-
f-vii
Are the handrails mounted 34 to 38 inches above the ramp surface? [ADA Standards § 4.8.5] Yes No...
-
4c.
Are the handrails mounted between 34 and 38 inches above the ramp surface? [ADA Stds 4.8.5] Yes _____ No _____...
-
§ 38.57(c)
(c) The diameter or width of the gripping surface of handrails and stanchions shall be 11/4 inches to 11/2 inches or provide an equivalent gripping surface and shall provide a minimum 11...
-
Aisle Stairs and Ramps in Assembly Areas
Sections 505.2 and 505.3 of the 2010 Standards provide exceptions for aisle ramp handrails....
-
Railings: ADA Standard Section 1005.2
Where provided, railings, guards, or handrails shall comply with 1005.2....
-
11B-1005.2 Railings
Where provided, railings, guards, or handrails shall comply with Section 11B-1005.2....
-
§ 38.155(a)
(a) Handrails and stanchions shall be provided in the entrance to the vehicle in a configuration which allows passengers to grasp such assists from outside the vehicle while starting to...
-
Can handrails overlap ramp landings?
Along runs and landings, the minimum clear width must be measured between the leading edge of handrails....
-
11B-604.7 Dispensers
Dispensers shall not be of a type that controls delivery or that does not allow continuous paper flow. [2010 ADAS] 604.7 Dispensers....
-
505.5 Clearance
Clearance between handrail gripping surfaces and adjacent surfaces shall be 1½ inches (38 mm) minimum. Figure 505.5 Handrail Clearance...
-
505.5 Clearance
Clearance between handrail gripping surfaces and adjacent surfaces shall be 1½ inches (38 mm) minimum. Figure 505.5 Handrail Clearance...
-
R409.9 Fittings
Handrails shall not rotate within their fittings. Where expansion joints are necessary for large spans of handrails, the expansion joint is permitted to rotate in its fitting....
-
4.9.4(1)
(1) Handrails shall be continuous along both sides of stairs. The inside handrail on switchback or dogleg stairs shall always be continuous (see Fig. 19(a) and (b))....