The NFPA Emergency Evacuation Planning Guide for People with Disabilities was developed in response to the emphasis that has been placed on the need to properly address the emergency procedure...
Search Results "RWD: Responsive Web Design"
Commonly Searched Documents
-
OVERVIEW
-
The Advance Notice of Proposed Rulemaking
The ANPRM dealt with the Department's responsibilities under both title II and title III. Public response to the ANPRM was extraordinary. ...
-
"Doing work'' or "performing tasks.'' (Section-by-Section Analysis)
The Department received a number of comments in response to the NPRM proposal urging the removal of the term ‘‘do work'' from the definition of a service animal....
-
Doing "work'' or "performing tasks.'' (Section-by-Section Analysis)
The Department received a number of comments in response to the NPRM proposal urging the removal of the term ‘‘do work'' from the definition of a service animal....
-
1009.2.4 Seat Height
The height of the lift seat shall be designed to allow a stop at 16 inches (405 mm) minimum to 19 inches (485 mm) maximum measured from the deck to the top of the seat surface when in the...
-
(8) the City's policies and procedures
(8) the City's policies and procedures regarding new construction and alterations, which do not require a close-out inspection for compliance with federal disability access design standards...
-
Technical Memorandum TM 2012-09 Employee Break Rooms
22, 2013 2012 TAS Reference: 212 and 804 In accordance with TAS 106.5.28, kitchenettes and break rooms are not employee work areas; therefore, they must be accessible and must be designed...
-
§27.7(d) Aid, benefits, or services limited by Federal law
For aid, benefits, or services authorized by Federal statute or executive order that are designed especially for persons with a disability, or for a particular class of persons with a disability...
-
On-Board Wheelchairs
On-Board Wheelchairs When required, on-board wheelchairs must be equipped with specific features and be designed to be compatible with the maneuvering space, aisle width, and seat height...
-
§35.170(c)
An individual may file a complaint with any agency that he or she believes to be the appropriate agency designated under subpart G of this part, or with any agency that provides funding...
-
101.1.4
to expand or diminish the defenses available to a place of public accommodation or a commercial facility under the Americans with Disabilities Act and the ADA Standards for Accessible Design...
-
A4.10.12 Car Controls
Industry-wide standardization of elevator control panel design would make all elevators significantly more convenient for use by people with severe visual impairments....
-
8.1 GENERAL
In addition to the requirements of 4.1 to 4.33, the design of all public areas of a library shall comply with 8, including reading and study areas, stacks, reference rooms, reserve areas...
-
2.5.1 Location
Depending on the design and location, the intersection of two ORARs may act as a resting interval. Exception....
-
Beach Access Route
A continuous, unobstructed path designed for pedestrian use that crosses the surface of a beach or that leads from a pedestrian access point to the high tide level at tidal beaches; mean...
-
§ 35.170(c) Where to file
An individual may file a complaint with any agency that he or she believes to be the appropriate agency designated under subpart G of this part, or with any agency that provides funding...
- Rakks® Brackets Installation Video
- Trace Research & Development Center
- Spinal Cord Injury Information Pages
-
1. Public Rights-of-Way
In addition, the guidelines address shared use paths, which are designed primarily for use by bicyclists, pedestrians and other authorized motorized and non-motorized users for transportation...
-
4.1 Wheeled Mobility Device Dimensions
Design for extremes of a range may help only a very few people, yet design for the mean or median may exclude those in the extremes which may be very useful in the design of facilities that...
-
810 Transportation Facilities
Response....
-
11B-104.1.1 Construction and manufacturing tolerances
Recognized tolerances are not intended to apply to design work. It is good practice when specifying dimensions to avoid specifying a tolerance where dimensions are absolute....
-
11B-104.1.1 Construction and manufacturing tolerances
Recognized tolerances are not intended to apply to design work. It is good practice when specifying dimensions to avoid specifying a tolerance where dimensions are absolute....