Measure running slope along the same lines of measurements as stated in Section 1.1.13 Although the F - number system can be used to measure surface flatness for smooth surfaces it requires...
Search Results "Check Writing Surface"
-
1.1.16 Alternate measurement tools
-
1016.5 Obstacles
EXCEPTION: Where the surface is other than asphalt, concrete, or boards, obstacles shall be permitted to not exceed 1 inch (25 mm) in height measured vertically to the highest point....
-
Section 35.151(i) Curb ramps (Section-by-Section Analysis)
Upon further consideration, however, the Department has concluded that the regulation should acknowledge that there are times when there are transitions from sidewalk to road surface that...
-
11B-1002.5 Amusement ride seats designed for transfer
Where possible, designers are encouraged to locate the ride seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
1007 Miniature Golf Facilities
This section covers miniature golf courses and contains specifications for accessible routes that take into account design conventions for miniature golf courses, such as carpeted play surfaces...
-
1132A.4, Item 2
wood decking with spaces) shall be the same level as the interior landing, except that secondary exterior doors may have no more than ½ inch (12.7 mm) of change in height between floor surfaces...
-
11B-411.2.1.5.1 Size
Buttons shall have square shoulders, be 3/4 inch (19.1 mm) minimum in the smallest dimension and shall be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding surface...
-
1132A.4, Item 2
wood decking with spaces) shall be the same level as the interior landing, except that secondary exterior doors may have no more than ½ inch (12.7 mm) of change in height between floor surfaces...
-
1009.2.4 Seat Height
The height of the lift seat shall be designed to allow a stop at 16 inches (405 mm) minimum to 19 inches (485 mm) maximum measured from the deck to the top of the seat surface when in the...
-
1018.6 Openings
Openings in the surface of beach access routes and resting intervals shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1018.6 Openings....
-
502.6 Identification
Signs shall be 60 inches (1525 mm) minimum above the finish floor or ground surface measured to the bottom of the sign....
-
11B-813.2.1.3 Height and operation
Adult changing table height shall be adjustable from 17 inches (432 mm) above the floor or ground to 38 inches (965 mm) above the floor or ground, as measured to the top of the changing surface...
-
11B-246.7 Trails and paths
Buildings and other functional areas shall be served by paths or walks with firm and stable surfaces....
-
1002.4.4.1 Width and Length
Wheelchair spaces shall provide a clear width of 30 inches (760 mm) minimum and a clear length of 48 inches (1220 mm) minimum measured to 9 inches (230 mm) minimum above the floor surface...
-
4e.
[ADA Stds 4.8.4] Yes _____ No _____ Note: The level landing may be part of the sidewalk or walking surface....
-
6c. Ramp Landing
[ADA Stds 4.8.4] Note: The level landing may be part of the sidewalk or walking surface. Yes _____ No _____...
-
Cal-Royal CR801 Series Hydraulic Door Closers
Non-handed for standard, top-jamb or parallel arm installation Hydraulic door closer with standard adjustable back-check function Non-sized, 1 thru 6....
-
Spinal Cord Injury Information Pages
Be sure to check out the spinal cord injury news blog. It's updated on a regular basis featuring current SCI news....
-
1193.23(a) (Advisory Guidance)
It does not require that such a process be submitted to any entity or that it even be in writing....
-
Complainant No. 1
The orthopedic surgeon offered to write a letter to another physician on behalf of the complainant, but did not take any other steps to refer him to another Aurora orthopedic surgeon....
-
§ 38.95(b)(13) Handrails
The handrail shall have a cross-sectional diameter between 11/4 inches and 11/2 inches or shall provide an equivalent grasping surface, and have eased edges with corner radii of not less...
-
Play Tables
Play Tables Play tables are surfaces, boards, slabs, or counters that are created for play....
-
Technical Memorandum TM 2012-04 Multi-Story Buildings and Facilities
The term “story” is defined in 106.5.64 as that portion of a building or facility designed for human occupancy included between the upper surface of a floor or the upper surface of the floor...
-
REFERENCES
Duvall, J., et al., Proposed Surface Roughness Standard for Pathways used by Wheelchairs. Transportation Research Board 93nd Annual Meeting, 2014(14-4494). 5....