The counter surface height shall be 38 inches (965 mm) maximum above the finish floor or ground....
Search Results "Transfer Surface"
-
11B-904.3.2 Counter
-
CURB RAMP
A sloping prepared surface, intended for pedestrian traffic, which provides access between a walk or sidewalk and a surface located above or below an adjacent curb face....
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
Handrail Extensions
ADAAG does not require handrails on sloped surfaces that have a rise of less than 6 inches or a projection less than 72 inches, or a slope of 1:20 (5%) or less....
-
Openings [1018.6]
Openings are gaps in the surface of a beach access route....
-
Outdoor Conditions [4.8.8]
Exterior ramps must be designed so that water does not accumulate on the ramp or landing surface. A slope up to 2% is allowed at landings for adequate drainage....
-
APPENDIX C
What was your pain/discomfort value associated with this surface (circle)?...
-
1011.4 Picnic Tables
This section requires picnic tables to comply with the technical requirements for dining surfaces in 902.3 of the Architectural Barriers Act Accessibility Guidelines, which requires the...
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
1133A.4 Countertops
A minimum linear length of 30 inches (762 mm) of countertop shall be provided for a work surface. ...
-
11B-703.4.1 Height above finish floor or ground
Tactile characters on signs shall be located 48 inches (1219 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest Braille cells and 60 inches (1524...
-
11B-705.2 Detectable directional texture
transit boarding platforms shall comply with Figure 11B-705.2 and shall be 0.1 inch (2.5 mm) in height that tapers off to 0.04 inch (1.0 mm), with bars raised 0.2 inch (5.1 mm) from the surface...
-
STORY
[DSA-AC] That portion of a building or facility designed for human occupancy included between the upper surface of a floor and upper surface of the floor or roof next above....
-
Literature Cited
Standard test method for shock-absorbing properties of playing surface systems and materials. ASTM F355-95, Vol. 15.07....
-
AJW Architectural Products U592 1.6 Gallon Sanitary Napkin Disposal w/ Keyed Access Panel & Mounted Shelf - Surface Mounted
Product Features Fabricated of #22 gauge stainless steel with a #4 satin finish Waste receptacle has a 1.5 gallon capacity Bottom panel is hinged for easy removal of...
-
609 Grab Bars
Specifications address size, spacing, position, surfaces, fittings, and structural strength....
-
2.7 Tread Obstacles
Where tread obstacles exist on the surface of an ORAR, they shall not exceed 1 inch (25 mm) in height....
-
Subject testing
A study was designed to investigate a correlation between surface roughness and WBV exposure to WC users in an attempt to determine which surfaces should be considered acceptable....
-
5. Significance and Use
5.1 This practice provides a means for obtaining a quantitative estimate of a surface property defined as roughness using longitudinal profile measuring equipment. 5.1.1 The PRI is portable...
-
Story
That portion of a building included between the upper surface of a floor and upper surface of the floor or roof next above....
-
1132A.4 Level floor or landing
Primary entry doors, required exit doors or secondary exterior doors with changes in height between the interior surface or floor level and the exterior surface or floor level shall comply...
-
Chapter 9: Built-In Elements
Chapter 9 covers built-in elements, including dining surfaces and work surfaces (902), benches (903), and sales and service counters (904)....
-
Handrail Extensions
ADAAG does not require handrails on sloped surfaces that have a rise of less than 6 inches or a projection less than 72 inches, or a slope of 1:20 (5%) or less....
-
Acknowledgments
Acknowledgments The development of objective surface measurement devices and objective surface testing was conducted with funding from the National Center for Medical Rehabilitation Research...
