For example, if the work is limited to specific elements, such as replacement of a lavatory and floor coverings, then at a minimum each altered element must comply with ADAAG....
Search Results "Minimum Dimension"
Filters
Commonly Searched Documents
-
Alterations [4.1.6(1), (2)]
-
ADA Standards for Accessible Design
These regulations adopt revised, enforceable accessibility standards called the 2010 ADA Standards for Accessible Design, which set minimum requirements—both scoping and technical—for newly...
-
308.3.1 Unobstructed
allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 48 inches (1220 mm) maximum and the low side reach shall be 15 inches (380 mm) minimum...
-
603.3 Mirrors
In order for mirrors to be usable by people who are ambulatory and people and people who use wheelchairs, the top edge of mirrors should be 74 inches (1880 mm) minimum from the floor or...
-
1134A.5, Item 5
When glass is used, it shall have minimum thickness of not less than 1/8 inch (3.17 mm) when fully tempered, or 1/4 inch (6.35 mm) when laminated, and shall pass the test requirements of...
-
1134A.6, Item 7
When glass is used, it shall have minimum thickness of not less than 1/8 inch (3.17 mm) when fully tempered, or ¼ inch (6.35 mm) when laminated, and shall pass the test requirements of this...
-
11B-308.3.1 Unobstructed
allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 48 inches (1219 mm) maximum and the low side reach shall be 15 inches (381 mm) minimum...
-
11B-224.4 Guest rooms with communication features
TABLE 11B-224.4 GUEST ROOMS WITH COMMUNICATION FEATURES Total Number Of Guest Rooms Provided Minimum Number Of Required Guest Rooms With Communication Features...
-
11B-303.3 Beveled
Changes in level between ¼ inch (6.4 mm) high minimum and ½ inch (12.7 mm) high maximum shall be beveled with a slope not steeper than 1:2. Advisory 11B-303.3 Beveled....
-
11B-812.7.2 Marking
Access aisle markings may extend beyond the minimum required length....
-
11B-603.3 Mirrors
In order for mirrors to be usable by people who are ambulatory and people who use wheelchairs, the top edge of mirrors should be 74 inches (1880 mm) minimum from the floor or ground. ◼...
-
11B-224.4 Guest rooms with communication features
TABLE 11B-224.4 GUEST ROOMS WITH COMMUNICATION FEATURES TOTAL NUMBER OF GUEST ROOMS PROVIDED MINIMUM NUMBER OF REQUIRED GUEST ROOMS WITH COMMUNICATION FEATURES...
-
Passing Spaces [1017.4]
used or the trail is not at the same level as the adjoining ground surface, such as a bridge crossing a ravine, increasing the frequency of passing spaces or widening the tread width to a minimum...
-
M301.2.1, M302.2.1 Transfer Height
M301.2.1, M302.2.1 Transfer Height Proposed requirement: The height of the transfer surface during patient transfer shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum...
-
11B-232.1 General
correctional facilities shall comply with the 2010 Standards except that public entities shall provide accessible mobility features complying with section 807.2 of the 2010 Standards for a minimum...
-
Clear Tread Width and Passing Spaces for Outdoor Recreation Access Routes
The minimum clear tread width of an outdoor recreation access route is 36 inches (915 millimeters), which is wide enough to allow unobstructed passage by a wheelchair....
-
Preliminary Guidelines for Vitri-Turf SEWF Installation
Allow the surface to cure for a minimum of 24 h. Cleanup Clean all tools and surface spots immediately with diesel fuel prior to drying....
-
Eye Height
The AASHTO Guide for the Development of Bicycle Facilities (p. 40) assumes a bicyclist eye height of 140 cm (54 inches) in calculating the minimum length of vertical curve necessary to provide...
-
Width
The AASHTO Guide for the Development of Bicycle Facilities (p. 5) recommends a minimum width of 120 cm (48 inches) for any facility designed to be used by bicyclists.(2) This is based on...
-
11B-232.1 General
correctional facilities shall comply with the 2010 Standards except that public entities shall provide accessible mobility features complying with section 807.2 of the 2010 Standards for a minimum...
-
Norton Surface Mounted 5700 Series Low Energy Door Operator
1601BF series door closer Non-Handed Unit Activation Options: wall switches, motion sensor, radio frequency device End-User On/Off Switch Hold Open options; 0-30 seconds (5 seconds minimum...
-
Sargent 6500 Line Lever Hardware with Lockset
" (13mm) throw Keys: Two, nickel silver Cylinder: Brass, 6 pin, LA keyway standard Finishes : 3, 4, 10, 10B, 26, 26D (No Split Finish) Door Prep: ANSI A115.2 (161) Modified Minimum...
-
Federal Elevator Serenus LULA Elevator
Stainless Steel Handrail Automatic control UL/CSA listed 14″ pit depth minimum Arrival gongs in cab Direction indicators in cab ADA Phone...
-
QuickCaption Remote Realtime Captioning CART
We have a two-hour per-day minimum, not per class/event. There is no charge for any class/event cancelled more than 48 hours in advance....
