If a curb ramp is provided, is the running slope of the ramp surface (not counting the side flares) no more than 1:12 or 8.33% [ADA Standards § 4.7.2] Yes No...
Search Results "Work Surface"
-
A6
-
M12
If a mirror is provided, is the bottom of the reflecting surface no higher than 40 inches above the floor or is a full length mirror provided?...
-
11B-1002.6.2 Transfer height
The height of transfer device seats shall be 14 inches (356 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
-
SECTION#2
SECTION#2 For the following questions, please answer every item pertaining to the trail surface composition....
-
Accessibility
Accessibility: When ceramic tile is used as the flooring surface, design professionals should consider the following, based on ANSI A108.01 and A108.02, where accessibility is a primary...
-
11B-1002.6.2 Transfer height
The height of transfer device seats shall be 14 inches (356 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
-
11B-1002.6.2 Transfer height
The height of transfer device seats shall be 14 inches (356 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
-
11B-705.1.2.1 Platform edges
Detectable warning surfaces at platform boarding edges shall be 24 inches (610 mm) wide and shall extend the full length of the public use areas of the platform....
-
705.2 Platform Edges
Detectable warning surfaces at platform boarding edges shall be 24 inches (610 mm) wide and shall extend the full length of the public use areas of the platform....
-
1008.3.2.1 Size
Transfer steps shall have level surfaces 14 inches (355 mm) deep minimum and 24 inches (610 mm) wide minimum....
-
1002.6.2 Transfer Height
The height of transfer device seats shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
-
1008.3.1.1 Size
Transfer platforms shall have level surfaces 14 inches (355 mm) deep minimum and 24 inches (610 mm) wide minimum....
-
LaCantina Doors - Contemporary Clad Industrial
New work for LaCantina Doors introducing their new Contemporary Clad product line. lacantinadoors.com/...
-
1118B.4
Surfaces for wheelchair spaces. Clear floor or ground spaces for wheelchairs shall comply with Section 1124B Ground and Floor Surfaces....
-
Preliminary Guidelines for SEWF Installation
Do not saturate surface with these lubricants. After compaction the thickness will be approximately 40 mm (1.6 in.). 3....
-
1630.16(a)
A religious corporation, association, educational institution, or society is permitted to give preference in employment to individuals of a particular religion to perform work connected...
-
Military Installation
Military installation does not include any facility used primarily for civil works, rivers and harbors projects, or flood control projects. ...
-
5. Site Constraints, Technical Infeasibility, and Unusually Expensive Remediation
Work on difficult sites may be postponed if there is an alternative accessible route within no more than 200 feet, to the maximum extent feasible. ...
-
4.3.11.1(7)
Pressurization equipment and its duct work within the building shall be separated from other portions of the building by a minimum two-hour fire-resistive construction....
-
Stress Management
reinforcement Refer to EAP Allow employee to make telephone calls for support Provide sensitivity training for workforce Allow the presence and use of a support animal Modify work...
-
§1630.16(a) Religious entities
A religious corporation, association, educational institution, or society is permitted to give preference in employment to individuals of a particular religion to perform work connected...
-
§ 38.23(b)(1) Design load
Working parts, such as cables, pulleys, and shafts, which can be expected to wear, and upon which the lift depends for support of the load, shall have a safety factor of at least six, based...
-
§ 38.95(b)(1) Design load
Working parts, such as cables, pulleys, and shafts, which can be expected to wear, and upon which the lift depends for support of the load, shall have a safety factor of at least six, based...
