(d) As a carrier, if you wish to use a different method of providing seating assignment accommodations to passengers with disabilities from those specified in this subpart, you must obtain...
Search Results "Seat Height"
-
§382.83(d)
-
§382.155(a)
(a) As a carrier providing service using aircraft with 19 or more passenger seats, you must respond to written complaints received by any means (e.g., letter, fax, e-mail, electronic instant...
-
§382.141(b)
(b) If you are a carrier that operates only aircraft with fewer than 19 passenger seats, you must provide training for flight crewmembers and appropriate personnel to ensure that they are...
-
607.7 Bathtub Enclosures
Enclosures for bathtubs shall not obstruct controls, faucets, shower and spray units or obstruct transfer from wheelchairs onto bathtub seats or into bathtubs....
-
607.7 Bathtub Enclosures
Enclosures for bathtubs shall not obstruct controls, faucets, shower and spray units or obstruct transfer from wheelchairs onto bathtub seats or into bathtubs....
-
Amusement Attraction
Amusement attractions include, but are not limited to, fun houses, barrels, and other attractions without seats....
-
AMUSEMENT ATTRACTION
Amusement attractions include, but are not limited to, fun houses, barrels and other attractions without seats....
-
AMUSEMENT ATTRACTION
Amusement attractions include, but are not limited to, fun houses, barrels and other attractions without seats....
-
Grab Bars: ADA Standard Section 604.5
Section 604.5 covers the current ADA Standards for grab bars that are used for water closets.
-
11B-809.10.5.2 Reinforcement for grab bars
The grab bar reinforcement shall be 8 inches (203 mm) minimum in height. b....
-
11B-809.10.5.2 Reinforcement for grab bars
The grab bar reinforcement shall be 8 inches (203 mm) minimum in height. b....
-
1023.9 Stairway identification signs
Section 1143A or Chapter 11B shall be located at the landing of each floor level, placed adjacent to the door on the latch side, in all enclosed stairways in buildings two or more stories in height...
-
1023.9 Stairway identification signs
Section 1143A or Chapter 11B shall be located at the landing of each floor level, placed adjacent to the door on the latch side, in all enclosed stairways in buildings two or more stories in height...
-
1134A.6, Item 4
The grab bar reinforcement shall be a minimum of 6 inches (152.4 mm) nominal in height. ...
-
1132A.4.1 Thresholds
Changes in height at interior door thresholds (e.g., floor material changes at door thresholds) shall not exceed ½ inch (12.7 mm). Thresholds shall comply with the following:...
-
1134A.6, Item 4
The grab bar reinforcement shall be a minimum of 6 inches (152.4 mm) nominal in height....
-
§ 38.153(c)(1)
(1) Doors shall have a minimum clear width when open of 30 inches (760 mm), measured from the lowest step to a height of at least 48 inches (1220 mm), from which point they may taper to...
-
11B-809.10.6.4 Reinforcement for grab bars
The grab bar reinforcement shall be 8 inches (203 mm) minimum in height....
-
11B-605.4 Flush controls
Hand operated flush controls shall comply with Section 11B-309 except that the flush control shall be mounted at a maximum height of 44 inches (1118 mm) above the finish floor....
-
810.5.3 Platform and Vehicle Floor Coordination
The height and position of a platform must be coordinated with the floor of the vehicles it serves to minimize the vertical and horizontal gaps, in accordance with the ADA Accessibility...
-
307 Protruding Objects
Several commenters called for the 27 inch triggering height to be reduced. Recommendations ranged from 15 to 6 inches....
-
810.5.3 Platform and Vehicle Floor Coordination
The height and position of a platform must be coordinated with the floor of the vehicles it serves to minimize the vertical and horizontal gaps, in accordance with the ADA Accessibility...
-
10.3.1(9)
(9) In stations covered by this section, rail-to-platform height in new stations shall be coordinated with the floor height of new vehicles so that the vertical difference, measured when...
-
Edge Protection [4.8.7]
Horizontal rails are another alternative although mounting heights are not specified (the 27 inch height in ADAAG Figure 17 pertains to the return of extensions as protruding objects)....