The top of the bench seat surface shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maximum above the finish floor or ground....
Search Results "Feasibility (Technical, Infeasible, Structural, Maximum Extent)"
-
11B-903.5 Height
-
11B-703.2.8 Line spacing
Spacing between the baselines of separate lines of raised characters within a message shall be 135 percent minimum and 170 percent maximum of the raised character height....
-
11B-1007.2 Accessible routes
Where accessible routes intersect playing surfaces of holes, a 1 inch (25 mm) maximum curb shall be permitted for a width of 32 inches (813 mm) minimum. 3. ...
-
11B-1007.2 Accessible routes
Where accessible routes intersect playing surfaces of holes, a 1 inch (25 mm) maximum curb shall be permitted for a width of 32 inches (813 mm) minimum. 3....
-
M305.2.4 Cross Section (Section-by-Section Analysis)
Specifically, the Access Board indicated it was considering requiring circular cross sections to have an outside diameter of 1¼ inches minimum and 2 inches maximum, and transfer supports...
-
Updates and Other Pocket Guides
Evan Terry Associates will continue to revise and update this Pocket Guide as new technical assistance is released and interpretations are provided by federal agencies....
-
Chapter 10: Recreation Facilities
Chapter 10 contains technical provisions for various types of recreation facilities....
-
Coat Hooks and Shelves
Section 213.3.7 addresses coat hooks and shelves provided in accessible toilet rooms, toilet compartments, and bathing facilities and references corresponding technical criteria for such...
-
Documenting Use of the Conditions for Exceptions on a Portion of a Trail or Beach Access Route [F204.4.1]
the conditions for exceptions on a portion of trail or a beach access route, Federal agencies should document in writing why they could not fully comply with a specific provision in the technical...
-
Perpendicular and Angled Parking Spaces (R309.3) (Section-by-Section Analysis)
The access aisle must be marked to discourage parking in the aisle and comply with the technical requirements for surfaces (see R302.7)....
-
1011.1 General
This section contains the technical requirements for outdoor constructed features provided within camping facilities, picnic facilities, viewing areas, and trailheads or on trails....
-
Interacting with People With Disabilities
To best prepare, you will want not only technical requirements but also the soft skills to support your event....
-
11B-606.6 Adjacent side wall or partition
See the foregoing ETA Editor's Note at 11B-212.3 regarding the difficulties of distinguishing fixture types and the applicable technical requirements....
-
II-6.6000 Curb ramps
Editor's Note See the 1994 Supplement: https://www.corada.com/documents/ada-title-ii-technical-assistance-manual-1994-supplement/ii-6-6000-curb-ramps...
-
11B-801.1 Scope
For example, Section 11B-806 addresses guest rooms in transient lodging facilities while Section 11B-902 contains the technical specifications for dining surfaces....
-
11B-903.1 General
This section provides the technical provisions for benches required to comply with Division 2 Scoping Requirements -- those in saunas, steam rooms, dressing, fitting and locker rooms, holding...
-
Transfer Protocols
The maximum and minimum transfer heights that were attainable were recorded....
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
1002.6.2 Transfer Height
The height of transfer device seats shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
-
§382.133(f)(3)
(3) The maximum weight and dimensions (length, width, height) of the device to be used by an individual that can be accommodated in the aircraft cabin consistent with the safety regulations...
-
11B-902.3 Height
The tops of dining surfaces and work surfaces shall be 28 inches (711 mm) minimum and 34 inches (864 mm) maximum above the finish floor or ground....
-
703.5.4 Character Proportions
Characters shall be selected from fonts where the width of the uppercase letter "O" is 55 percent minimum and 110 percent maximum of the height of the uppercase letter "I"....
-
902.3 Height
The tops of dining surfaces and work surfaces shall be 28 inches (710 mm) minimum and 34 inches (865 mm) maximum above the finish floor or ground....
-
703.5.4 Character Proportions
Characters shall be selected from fonts where the width of the uppercase letter "O" is 55 percent minimum and 110 percent maximum of the height of the uppercase letter "I"....