ADOPTION OF A 19 INCH HEIGHT MINIMIZES COSTS TO HEALTH CARE PROVIDERS In the absence of Committee consensus commending a departure from the existing broadly accepted transfer surface...
Search Results "Transfer Surface"
-
ADOPTION OF A 19 INCH HEIGHT MINIMIZES COSTS TO HEALTH CARE PROVIDERS
-
How is slip resistance measured?
The coefficient of friction between the two surfaces is the ratio of the horizontal and vertical forces required to move one surface over another to the total force pressing the two surfaces...
-
PART 3: ACCESSIBLE EXAMINATION ROOMS
.); and adequate clear floor space inside the room for side transfers and use of lift equipment....
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
Zurn Insulation Combination Kit: One Trap Protector, Two Stop Supply Protectors and One Offset Drain Protector
Protector, Two Stop Supply Protectors and One Offset Drain Protector FEATURES: Satin white PVC resin 3/8" Nominal wall with vandal resistant clips ADA compliant and resists thermal transfer...
-
Detectable Warning
A standardized surface feature built in or applied to walking surfaces or other elements to warn visually impaired people of hazards on a circulation path....
-
TACTILE WARNING
A standardized surface texture applied to or built into walking surfaces or other elements to warn visually impaired people of hazards in the path of travel....
-
StaLok
During the testing performed in August 2007, it was noted that an individual had walked on the surface at the Wetlands dedication and left marks in the surface of a depth of approximately...
-
3.2 MDE Advisory Committee Process
In all cases except one – the minimum height of transfer surfaces – the Committee reached consensus on the recommended accessibility standards (see Section 5)....
-
1.4 Overview of Report
Section 6 briefly introduces the standard about which Committee members did not reach consensus: the minimum transfer surface height....
-
§382.57(c)(6)(i) Input controls
Where provided, key surfaces not on active areas of display screens, must be raised above surrounding surfaces....
-
Recommendations
Recommendations Based on the data in Table 1 and the observations above, we recommend: a minimum flat surface of 40 in. length for platforms accommodating wheeled mobility devices...
-
§27.71(k)(6)(i) Input controls.
Where provided, key surfaces not on active areas of display screens, must be raised above surrounding surfaces....
-
§ 382.57(c)(6)(i) Input controls
Where provided, key surfaces not on active areas of display screens, must be raised above surrounding surfaces....
-
§ 27.71(k)(6)(i) Input controls
Where provided, key surfaces not on active areas of display screens, must be raised above surrounding surfaces....
-
Georgia-Pacific Compact® Side-By-Side Double Roll Bathroom Tissue Dispenser 56784
Featuring a transfer paddle to prevent access to a new roll before the current roll is completely used up, this dispenser offers one of the most cost-effective solutions for high-capacity...
-
Brewer Access™ High-Low Exam Table 700
In addition, only Brewer's Access High-Low Exam Table design provides an 18" profile in the seated position to allow level transfer from standard wheelchair heights, complete with upright...
-
505.5 Clearance
Clearance between handrail gripping surfaces and adjacent surfaces shall be 1½ inches (38 mm) minimum. Figure 505.5 Handrail Clearance...
-
4.8.5(5)
(5) Top of handrail gripping surfaces shall be mounted between 34 in and 38 in (865 mm and 965 mm) above ramp surfaces....
-
11B-904.4.1 Parallel approach
A portion of the counter surface that is 36 inches (914 mm) long minimum and 34 inches (864 mm) high maximum above the finish floor shall be provided....
-
11B-904.4.1 Parallel approach
A portion of the counter surface that is 36 inches (914 mm) long minimum and 34 inches (864 mm) high maximum above the finish floor shall be provided....
-
11B-809.2.2 Turning space
For example, in kitchens, Section 11B-804.3.1 requires at least one work surface with clear floor space complying with Section 11B-306 to be centered beneath....
-
11B-809.2.2 Turning space
For example, in kitchens, Section 11B-804.3.1 requires at least one work surface with clear floor space complying with Section 11B-306 to be centered beneath....
