Through penetrations of fire-resistance-rated horizontal assemblies shall comply with Section 711.4.1.1 or 711.4.1.2....
Search Results "Designated Aisle Seat (Assembly)"
-
711.4.1 Through penetrations
-
4.3.5 Patient Positions During Diagnostic Imaging
Some nuclear medicine (NM) equipment has a unique design created for convenience: in this design, the table pivots out of the way to allow a scan of a patient seated in a chair or wheelchair...
-
11B-502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings....
-
502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings....
-
11B-502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings. ...
-
11B-502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings....
-
11B-903.4 Back support
Back support shall be 48 inches (1219 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (457 mm) minimum above the seat...
-
11B-903.4 Back support
Back support shall be 48 inches (1219 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (457 mm) minimum above the seat...
-
Pilot Rock XT Series Side Accessible Picnic Table Using Aluminum
“Skid” design permits movement without damage to turf. Model XT 6 and 8 ft....
-
Pilot Rock UT Series Side Accessible Picnic Table Using Aluminum
Model UT Side Accessible Picnic Tables are designed for most public applications. Built rugged, but with less weight, easier to move. ...
-
Conclusions
It focuses solely on the adequacy of these transfer surface dimensions for a static seating surface....
-
General: ADA Standard Section 706.1
Assistive listening systems required in assembly areas shall comply with 706. Advisory 706.1 General....
-
4.1.3 Adjustable Height Chairs with and without Footplates
a minimum 2” clearance is required from the floor to the bottom of the footplate as specified by domestic UL and International Electrotechnical Commission (IEC) standards (as currently designed...
-
Attachment A: Violations Identified in the United States' Letter of Findings (Sept. 29, 2014)
[See subsections ...]
-
Sec.36.403(c)(1)(iii)
(iii) Redesigning the assembly line area of a factory; or...
-
§ 36.403(c)(1)(iii)
(iii) Redesigning the assembly line area of a factory; or...
-
11B-812.1 General
Where vehicle spaces and access aisles are marked with lines, measurements shall be made from the centerline of the markings....
-
11B-812.1 General
Where vehicle spaces and access aisles are marked with lines, measurements shall be made from the centerline of the markings....
-
11B-106.5 Defined terms
. ◼ ACCESS AISLE ACCESSIBILITY ACCESSIBLE ACCESSIBLE ELEMENT ACCESSIBLE MEANS OF EGRESS ACCESSIBLE ROUTE ACCESSIBLE SPACE ADAPTABLE ADDITION ADJUSTED CONSTRUCTION...
-
Texas Department of Transportation (TxDOT) Computer Aided Drawings Standard Plan Files
Any modifications to a statewide or district standard file, however minor, must be documented briefly and dated in the revision block of the sheet, and the designation "(MOD)" must be appended...
-
F234.1 General
These requirements apply generally to newly designed and constructed amusement rides and attractions....
-
234.1 General
These requirements apply generally to newly designed and constructed amusement rides and attractions....
-
234.1 General
These requirements apply generally to newly designed and constructed amusement rides and attractions....
-
D.
The Department began receiving complaints from persons with disabilities regarding a new design of movie theaters across the country, including stadium-style movie theaters owned and/or...
