Is the elevator equipped with audible tones or bells or verbal annunciators that announce each floor as it is passed? [ADA Standards § 4.10.13] Yes No...
Search Results "Court Floor Holding Cell"
-
e-vii
-
4.15.2* Spout Height
Spouts shall be no higher than 36 in (915 mm), measured from the floor or ground surfaces to the spout outlet (see Fig. 27(a))....
-
5.1.4 Turning Space
Where the camp shelter floor is not elevated above the trail or ORAR, as applicable, a turning space complying with ABAAS section 304.3 shall be provided....
-
4.19.6* MIRRORS
Mirrors shall be mounted with the bottom edge of the reflecting surface no higher than 40 in (1015 mm) from the floor (see Fig. 31)....
-
M303.2.4.1 Toe Clearance
Toe clearance shall be provided at a height of 9 inches (230 mm) above the floor to a depth of 6 inches (150 mm) maximum....
-
1134A.5, Item 2
A bathtub installed without surrounding walls shall provide reinforced areas for the installation of floor-mounted grab bars....
-
1134A.5, Item 2
A bathtub installed without surrounding walls shall provide reinforced areas for the installation of floor-mounted grab bars....
-
Additional Transfer Techniques: Use of Stretchers and Gurneys
Additional Transfer Techniques: Use of Stretchers and Gurneys Some equipment, including radiologic equipment, lacks space underneath necessary for a portable floor lift to be used....
-
What materials may satisfy ADAAG requirements?
If there is a choice between flooring materials otherwise suitable for a particular application, we recommend choosing the material with the higher coefficient of friction, particularly...
-
Bobrick ClassicSeries Toilet Tissue Dispenser for Two Rolls B-2740
Holds two rolls up to 6" (150mm) diameter (2000 sheets). Unit 12 1⁄2" (320mm) wide, proj. 4 7⁄8" (125mm) from wall. No controlled delivery....
-
Mockett PTH1-SSS 13-3/16" Paper Towel Holder
DESCRIPTION Wall-mounted satin stainless bar with screw cover plate and small retaining pin to hold roll in place. Size: 13 3/16" length, projects 3 13/32" from wall....
-
Camp Shelters
The long side of the clear floor or ground space must be parallel to the camp shelter entrance....
-
Norton Surface Mounted Light Duty 210 Series Door Closer
Independent latch sweep and backcheck intensity valves Full plastic cover Closer footprint: 3/4" x 12" Projection: 2-1/8" Available in 689 (aluminum) and 690 (dark bronze) finishes Non-hold...
-
M-D Building Products, Inc. GEN2 SmartTool™ Digital Level
rate increases as angle is approached Steady beep when angle achieved Changes tone when gone too far Perfect for shimming cabinets, leveling pool tables Angle Copy Hold...
-
11B-409.4.4 Leveling
Each car shall automatically stop at a floor landing within a tolerance of ½ inch (12.7 mm) under rated loading to zero loading conditions....
-
407.4.6.2 Buttons
Car control buttons with floor designations shall comply with 407.4.6.2 and shall be raised or flush. EXCEPTION: In existing elevators, buttons shall be permitted to be recessed....
-
707.7.1 Visibility
The display screen shall be visible from a point located 40 inches (1015 mm) above the center of the clear floor space in front of the machine....
-
11B-707.7.1 Visibility
The display screen shall be visible from a point located 40 inches (1016 mm) above the center of the clear floor space in front of the machine....
-
902.4.2 Height
The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (760 mm) maximum above the finish floor or ground....
-
409.4.4 Leveling
Each car shall automatically stop at a floor landing within a tolerance of ½ inch (13 mm) under rated loading to zero loading conditions....
-
6. Toilet Seat
Is the toilet seat in each accessible toilet room between 17"-19" above the floor? [ADA Stds. 4.16.3] Yes __ No __ N/A __ Comments: _____________________________________...
-
H28
Is the surface of the toilet seat in this 36-inch-wide stall 17 to 19 inches above the floor? [ADA Standards §§ 4.16.3; 4.22.4] Yes No...
-
11B-902.4.2 Height
The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (762 mm) maximum above the finish floor or ground....
-
11B-904.5.2 Tray slides
The tops of tray slides shall be 28 inches (711 mm) minimum and 34 inches (864 mm) maximum above the finish floor or ground....
