Parking spaces and pull-up spaces for recreational vehicles shall be 20 feet (6100 mm) wide minimum....
Search Results "Pick-Up Counter"
Filters
Commonly Searched Documents
-
1012.2 Recreational Vehicles
-
11B-707.3 Operable parts
SECTION TITLE NOTES 11B-707.3 Operable parts. Provides exceptions to technical...
-
1012.1 General
This section contains the technical requirements for parking spaces provided within camping units and picnic units with mobility features and pull-up spaces for recreational vehicles at...
-
Width of Spaces [1012.2]
Parking spaces and pull-up spaces for RVs must be at least 20 feet wide to accommodate RVs equipped with a lift (figure 27)....
-
F231.4.2 Partitions
Where solid partitions or security glazing separate visitors from detainees, at least one of each type of cubicle or counter partition shall comply with 904.6....
-
231.4.2 Partitions
Where solid partitions or security glazing separate visitors from detainees at least one of each type of cubicle or counter partition shall comply with 904.6....
-
231.4.2 Partitions
Where solid partitions or security glazing separate visitors from detainees, at least one of each type of cubicle or counter partition shall comply with 904.6....
-
11B-231.4.2 Partitions
Where solid partitions or security glazing separate visitors from detainees at least one of each type of cubicle or counter partition shall comply with Section 11B-904.6....
-
11B-231.4.2 Partitions
Where solid partitions or security glazing separate visitors from detainees at least one of each type of cubicle or counter partition shall comply with Section 11B-904.6....
-
11B-231.4.2 Partitions
Where solid partitions or security glazing separate visitors from detainees at least one of each type of cubicle or counter partition shall comply with Section 11B-904.6....
-
A1
Is a relatively level (1:50 or 2% maximum slope in all directions) access aisle provided adjacent and parallel to the side of the vehicle pull-up area?...
-
Height: ADA Standard Section 902.3
The tops of dining surfaces and work surfaces shall be 28 inches (710 mm) minimum and 34 inches (865 mm) maximum above the finish floor or ground.
-
11B-902.3 Height
The tops of dining surfaces and work surfaces shall be 28 inches (711 mm) minimum and 34 inches (864 mm) maximum above the finish floor or ground.
-
Accessible Route Into and Through the Business
If construction or repair requires customers to detour around taped-off areas or to step up on plywood walkways, ensure that the temporary route is accessible or that there is an alternate...
-
231.4 Visiting Areas
231.4 Visiting Areas. Visiting areas shall comply with 231.4.
-
F231.4 Visiting Areas
Visiting areas shall comply with F231.4.
-
11B-231.4 Visiting areas
Visiting areas shall comply with 11B-231.4.
-
231.4 Visiting Areas
Visiting areas shall comply with 231.4.
-
1133A.4.1 Exceptions
Exceptions: Stone, cultured stone and tiled countertops may be used without meeting the repositioning requirements. Two 15-inch (381 mm) wide minimum breadboards may...
-
1133A.4, Item 1
1. A minimum linear length of 30 inches (762 mm) of countertop shall be provided for the kitchen sink installation.
-
7.3(3)
(3) Signage identifying accessible check-out aisles shall comply with 4.30.7 and shall be mounted above the check-out aisle in the same location where the check-out number or type of...
-
4.7.2 Slope
Slopes of curb ramps shall comply with 4.8.2. The slope shall be measured as shown in Fig. 11. Transitions from ramps to walks, gutters, or streets shall be flush and free of abrupt...
-
4.7.2 SLOPE
Slopes of curb ramps shall comply with 4.8.2. The slope shall be measured as shown in Fig. 11. Transitions from ramps to walks, gutters, or streets shall be flush and free of abrupt...
-
11B-231.4 Visiting areas
Visiting areas shall comply with 11B-231.4.