Exception: Â Where sloped entries are provided, the surfaces shall not be required to be slip resistant....
Search Results "Surface Material"
Filters
Commonly Searched Documents
-
11B-1009.3.1 Sloped entries
-
R407.9.2 Curb or Barrier
A curb or barrier shall be provided that prevents the passage of a 100 mm (4 in) diameter sphere, where any portion of the sphere is within 100 mm (4 in) of the finish surface....
-
T702.8 Contrast
Where provided, protective surfaces over signs shall have a non-glare finish....
-
1009.3.1 Sloped Entries
Sloped entries shall comply with Chapter 4 except as modified in 1109.3.1 through 1109.3.3 EXCEPTION: Where sloped entries are provided, the surfaces shall not be required to be slip...
-
M302.3.2 Armrests
Armrests on transfer sides are not permitted to obstruct access to the transfer surface. See M302.2.3 Exception....
-
11B-1009.3.1 Sloped entries
Exception: Where sloped entries are provided, the surfaces shall not be required to be slip resistant....
-
11B-705.1.2.1 Platform edges
Detectable warning surfaces at platform boarding edges shall be 24 inches (610 mm) wide and shall extend the full length of the public use areas of the platform....
-
11B-1009.3.1 Sloped entries
Exception:Â Where sloped entries are provided, the surfaces shall not be required to be slip resistant....
-
PEMKO 5" Latching Panic Saddle Threshold No. 2009-PK
About Commercial Thresholds Pemko manufactures thresholds in several materials to meet customer needs. Extruded Aluminum thresholds are manufactured of tempered aluminum, 6063-T6....
-
Wetland Trail Design and Construction
Little has been published on wetland trail construction, and materials that are available are often outmoded or are too regionally focused....
-
1133A.7.1 Plumbing protection
There shall be no sharp or abrasive surfaces under kitchen sinks....
-
405.9.2 Curb or Barrier
curb or barrier shall be provided that prevents the passage of a 4 inch (100 mm) diameter sphere, where any portion of the sphere is within 4 inches (100 mm) of the finish floor or ground surface...
-
Technical Requirements [1017]
The technical requirements for trails include specific provisions for the surface, clear tread width, passing spaces, tread obstacles, openings, running slope, cross slope, resting intervals...
-
T402.8.1 Deployment to Roadways or to Curb Height Boarding and Alighting Areas
bridgeplates used for deployment to the roadway or to curb-height boarding and alighting areas shall be 1:6 maximum, as measured to ground level with the non-rail vehicle resting on a flat surface...
-
TRANSIT BOARDING PLATFORM
[DSA-AC] Â A horizontal, generally level surface, whether raised above, recessed below or level with a transit rail, from which persons embark/disembark a fixed rail vehicle....
-
405.9.2 Curb or Barrier
curb or barrier shall be provided that prevents the passage of a 4 inch (100 mm) diameter sphere, where any portion of the sphere is within 4 inches (100 mm) of the finish floor or ground surface...
-
3.2 MDE Advisory Committee Process
The Subcommittees issued Reports about their deliberations and recommendations and they are provided as supporting materials to this report....
-
Railings—Guardrails, Handrails, and Safety
Choose materials carefully; determine how many railings will be provided based on safety considerations rather than convention, and so forth....
-
Bobrick Recessed Sharp Disposal B-35016
Product Warranty Guide Specification LEED Contribution Country of Origin Materials Cabinet — Heavy gauge stainless steel....
-
1134A.5 Bathtubs
The edge of the clear floor space shall be flush with the control wall surface....
-
National Braille Association
National Braille Association, founded in 1945, is a non-profit organization dedicated to providing continuing education to those who prepare braille, and to providing braille materials to...
-
1133A.2, Item 3
A clear floor space at least 30 inches (762 mm) by 48 inches (1219 mm) that allows either a parallel or a forward approach shall be provided at the work surface required by Section 1133A...
-
1002.5.2 Transfer Height
The height of amusement ride seats designed for transfer shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area....
-
Note
As shown, there are several ways for grab bars to be designed with adequate gripping surfaces, while ensuring that nothing can be tied onto them....
