feasible," as used in this section, applies to the occasional case where the nature of an existing facility makes it virtually impossible to comply fully with applicable accessibility standards...
Search Results "ISO: International Organization for Standardization"
Commonly Searched Documents
-
Maximum Extent Feasible
-
Automatic Teller Machines and Fare Machines: ADA Standard Section 707
Federal procurement law requires that ITMs purchased by the Federal government comply with standards issued by the Access Board under Section 508 of the Rehabilitation Act of 1973, as amended...
-
1.1.8 City, county, or city and county amendments, additions or deletions
Local modifications shall comply with Health and Safety Code Section 18941.5 for Building Standards Law, Health and Safety Code Section 17958 for State Housing Law or Health and Safety Code...
-
11B-806.2.3 Sleeping areas
[2010 ADA Standards] 806.2.3 Sleeping Areas. At least one sleeping area shall provide a clear floor space complying with 305 on both sides of a bed....
-
11B-206.4.4.1 Location
[2010 ADA Standards] 206.4.4.1 Location....
-
11B-604.7 Dispensers and disposal units
[2010 ADA Standards] 604.7 Dispensers....
-
11B-703.3 Braille
Standard English uses contractions like "don't" as a short way of writing two words, such as "do" and "not." In Braille there are many additional contractions....
- Beneficial Designs The Universal Trail Assessment Process (UTAP)
-
Toward Independence and The ICD Survey of Disabled Americans
NCD chose to take responsibility for the report rather than simply contracting an outside organization to do it....
-
Safe Harbor
Elements that do not comply with the requirements for those elements in the 1991 Standards must be modified to the extent readily achievable....
-
Section 36.406(d) Social Service Establishments (Section-by-Section Analysis)
The two design standards for accessibility (i.e., the 1991 Standards and UFAS) have confronted many social service providers with separate, sometimes conflicting requirements for the design...
-
Section 35.151(e) Social Service Establishments (Section-by-Section Analysis)
The two design standards for accessibility--i.e., the 1991 Standards and UFAS--have confronted many social service providers with separate, and sometimes conflicting, requirements for design...
-
4.3.8 Operating forces
Moreover, the standards preclude the use of a pinch grip, which is desirable to people who are able to use it effectively....
-
Triggering event
In Sec. 35.151(c)(2) of the NPRM, the Department proposed that the commencement of construction serve as the triggering event for applying the proposed standards to new construction and...
-
Literature Cited
Standard test method for shock-absorbing properties of playing surface systems and materials. ASTM F355-95, Vol. 15.07....
-
6.2 PV Systems at Existing Parking Facilities
6.2 PV Systems at Existing Parking Facilities 6.2A – Parking Fully Covered - The PV system covers all of the standard parking, accessible parking, or code compliant location for accessible...
-
3.3.1 Unoccupied Device Width
For example, our results for mean unoccupied width are just under the U.S. standard reference wheelchair of 660 mm (26 in.)....
-
Introduction
These regulations include detailed architectural requirements known as the ADA Standards for Accessible Design (ADA Standards), 28 C.F.R. pt. 36, Appendix A....
-
Triggering event. (Section-by-Section Analysis)
In § 35.151(c)(2) of the NPRM, the Department proposed that the commencement of construction serve as the triggering event for applying the proposed standards to new construction and alterations...
-
Subpart F—Certification of State Laws or Local Building Codes (Section-by-Section Analysis)
were determined in the past to meet or exceed the 1991 Standards....
-
231 and 808 Judicial Facilities and Courtrooms
231 and 808 Judicial Facilities and Courtrooms Section 231 of the 2010 Standards adds requirements for accessible courtrooms, holding cells, and visiting areas....
-
§ 1194.26(d)
(d) Where provided, at least one of each type of expansion slots, ports and connectors shall comply with publicly available industry standards....
-
C1-a
[ADA Standards § 4.1.2(1), 4.3] Yes No...
-
J3
[ADA Standards § 4.15.2] Yes No...