MRXA series is ANSI Grade 1 mortise lock set with 5-Point ligature resistant arch trim. It is applicable for new or retrofit application. US patent # 9033375. ...
Search Results "ANSI: American National Standards Institute"
Filters
Commonly Searched Documents
-
TownSteel MRXA Grade 1 Mortise Lock with Ligature Resistant Trim
-
TownSteel MRXL Grade 1 Mortise lock with Ligature Resistant Escutcheon
MRXL series is ANSI Grade 1 mortise lock set with ligature resistant lever trim. MRX-E-L provides escutcheon trim for new or retrofit application....
-
TownSteel MRXL Grade 1 Mortise Lock with Ligature Resistant Rose Trim
MRXL series is ANSI Grade 1 mortise lock set with ligature resistant lever trim. MRX-S-L provides rose trim for new or retrofit application....
-
Rebuilding Together Charles County (Christmas in April) - Waldorf, MD
In 1982, a national headquarters was established in Washington, D.C....
-
Executive Summary
The U.S. standards are based on research completed in the late 1970’s....
-
Aisle Stairs and Ramps in Assembly Areas
access must comply with the technical requirements for stairs set out in section 4.9 of the 1991 Standards....
-
SCI Empowerment Project by University of Washington Department of Rehabilitation Medicine
Department of Rehabilitation Medicine at University of Washington Medical Center and Harborview Medical Center, is one of only 14 model spinal cord injury (SCI) centers funded by the National...
-
Design Guidelines for the Visual Environment
This guideline was developed by the Low Vision Design Committee of the National Institute of Building Sciences (NIBS) through initial funding from the U.S....
-
Section 1194.24 Video and Multimedia Products (Preamble, Section-by-Section Analysis)
These non-receiver displays are commonly used throughout the government and in educational institutions and therefore, should have the capability to decode closed captions....
-
Mono Jacks, Sound Pressure, Etc
Section 4.33.7 of the 1991 Standards does not contain specific technical requirements for assistive listening systems....
-
C102.1 Incorporation by Reference
Where conflicts occur between the 255 Guidelines and the referenced standards, these guidelines apply....
-
§ 35.151(c)(2)
alterations commence on or after September 15, 2010 and before March 15, 2012, then new construction and alterations subject to this section may comply with one of the following: The 2010 Standards...
-
16(a)(i)
(i) The hotel has the required number of accessible rooms for guests with mobility disabilities required by ADA Standards § 9.1.2, the required number of accessible rooms with roll-in showers...
-
§ 35.151(c)(5)(i)
(i) Newly constructed or altered facilities or elements covered by §§35.151(a) or (b) that were constructed or altered before March 15, 2012, and that do not comply with the 1991 Standards...
-
11B-503.3.3 Marking
[2010 ADA Standards] 503.3.3 Marking. Access aisles shall be marked so as to discourage parking in them....
-
7.1 Basic Understanding of Diagnostic Imaging Equipment
As described in Section 4, in contrast to compact and mobile imaging technologies such as ultrasound and echocardiography machines, the imaging equipment covered by the accessibility standards...
-
Allegion aptiQmobile Credentials Mobile Application
your life aptiQ’s NFC-enabled readers can be installed anywhere giving students and employees access to secured buildings and the convenience of services like these: Educational Institutions...
-
Hager Companies Cast Pull 5N
Cast Door Pull Materials: - Aluminum, brass, bronze, stainless steel Options: - May be combined with a plate to make a pull plate Certification: - Meets ANSI A156.6 for J401 Pulls...
-
Hager Companies Cast Pull 6N
Cast Door Pull Materials: - Aluminum, brass, bronze, stainless steel Options: - May be combined with a plate to make a pull plate Certification: - Meets ANSI A156.6 for J401 Pulls...
-
Hager Companies Oval Wrought Door Pull 9
Oval Wrought Door Pull Materials: - Brass, Bronze, Stainless Steel Options: - May be combined with a plate to make a pull plate Certification: - Meets ANSI A156.6 for J401 Pulls...
-
Don-Jo Mfg., Inc. Door Viewers ULDV 180
Number ULDV 180 Dimensions 180 Degrees Ansi L23221 Shelf pack 10 Finishes 605, 626 Features...
-
Don-Jo Mfg., Inc. Door Viewers DV 180
Number DV 180 Dimensions 180 Degrees Ansi L21371 Shelf pack 10 Finishes 605, 626 Features...
-
Don-Jo Mfg., Inc. Door Viewers DV 90
Number DV 90 Dimensions 160 Degrees Ansi L21372 Shelf pack 10 Finishes 605, 626 Features Plastic...
-
§100.201a(a)
(a) The following standards are incorporated by reference into 24 CFR part 100 pursuant to 5 U.S.C. 552(a) and 1 CFR part 51, as though set forth in full....
