address the width of parking spaces and pull-up spaces for recreational vehicles (1012.2); the width of parking spaces for vehicles, other than recreational vehicles (1012.3); and the surface...
Search Results "Tread Surface"
Filters
Commonly Searched Documents
-
1012.1 General
-
1132A.4, Item 3
Secondary exterior doors onto decks, patios, or balcony surfaces constructed of impervious materials (e.g., concrete, brick, flagstone) may have a maximum change in height from the interior...
-
Alterations and Additions
Normal maintenance, such as pothole repair, surface patching, or repainting in place existing striping for a few spaces, is not considered an alteration except where it affects a facility...
-
§ 37.91(e)
Appropriate auxiliary aids and services include providing a hard surface on which to eat....
-
Expert opinion on current literature
There is a consensus among studies that transferring to a higher surface implies greater exertion of the upper limb (3-6) . ...
-
Taking Measurements
Taking Measurements Sloped Surfaces One way to measure slope is to use a 24-inch level with leveling bubble and a tape measure....
-
What was measured and why?
Often, an unstable surface, for example, may be perceived as very difficult because of the unstable footing, even though the individual does not have to exert him/herself....
-
Dune Crossings [1018.10]
The handrails must be continuous at a height of 34 to 38 inches above the walking surface along both sides of the dune crossing (figure 32)....
-
New Construction
Dining and Work Surfaces -- Sections 226 and 902. The provisions regarding accessible routes in section 206.2.5 (Restaurants and Cafeterias) also apply to dining surfaces....
-
Transit Stops (R308.1) (Section-by-Section Analysis)
The surfaces of boarding and alighting areas and boarding platforms must comply with the technical requirements for surfaces (see R302.7)....
-
406.8 Detectable Warnings
width of the curb ramp (exclusive of flared sides) and shall extend either the full depth of the curb ramp or 24 inches (610 mm) deep minimum measured from the back of the curb on the ramp surface...
-
1009.5.2 Transfer Space
A transfer space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer platform surface and shall...
-
A7. Curb Ramps
Is the ramp surface at least 36” wide, excluding flared sides? [ADA Stds 4.7.3] Yes _____ No _____ b. Is the slope (up or down the ramp) no more than 1:12? ...
-
R308.1 Transit Stops
Transit stops should be located so that there is a level and stable surface for boarding vehicles....
-
11B-812.7.2 Marking
The color of the borderlines, hatched lines, and letters shall contrast with that of the surface of the access aisle....
-
1018.2 Aisles in assembly spaces
for applications listed in Section 1.9.1 regulated by the Division of the State Architect-Access Compliance, shall also comply with Chapter 11A or Chapter 11B, Section 11B-403 _|Walking Surfaces...
-
11B-505.10 Handrail extensions
Handrail gripping surfaces shall extend beyond and in the same direction of stair flights and ramp runs in accordance with Section 11B-505.10....
-
Conditions for Exceptions [1019]
and the prevailing construction practices for this type of setting do not include blasting, blasting does not have to be used to remove a rock outcrop in order to comply with the clear tread...
-
Track Crossing
The proposed rule required route surfaces to be level with the rail top, but permitted a 2 ½ inch gap at the inner edge of rails to accommodate wheel flanges (1003.2.7)....
-
What Are the Requirements for Accessible Routes?
This section describes the various features of accessible routes within a play area, including location, clear width, slope, and accessible surfaces. ...
-
403.5.1 Clear Width
Except as provided in 403.5.2 and 403.5.3, the clear width of walking surfaces shall be 36 inches (915 mm) minimum....
-
1018.5 Obstacles
EXCEPTION: Where the surface is other than asphalt, concrete, or boards, obstacles shall be permitted to not exceed 1 inch (25 mm) in height measured vertically to the highest point....
-
R406 Reach Ranges (Section-by-Section Analysis)
R406 Reach Ranges (Section-by-Section Analysis) Forward and side reach ranges must be between 380 millimeters (1.25 feet) and 1220 millimeters (4 feet) above the finish surface....
-
f-iv
[ADA Standards § 4.8.4] Yes No Note: The level landing may be part of the sidewalk or walking surface. Notes: 1. At least 36 inches between handrails 2....