Type 304, 18 Gauge Stainless Steel. 24" Length x 1-1/2" Diameter with concealed screws Brushed stainless finish Grab bar to wall distance 1-1/2" ADA...
Search Results "Transfer Access"
Filters
Commonly Searched Documents
-
Just Manufacturing 24" Stainless Steel Grab Bar
-
Just Manufacturing 36" Stainless Steel Grab Bar
Type-304, 18 Gauge Stainless Steel 36" Length x 1-1/2" Diameter with concealed screws Brushed stainless finish Grab bar to wall distance...
-
Bobrick 36" Straight Grab Bar Peened B-6806.99 x 36
36" (915mm) long, 1-1/2" (38mm) dia. tubing, peened finish. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick,...
-
Bobrick 36" Straight Grab Bar B-5806 x 36
36" (915mm) long, 1-1/4" (32mm) dia. tubing. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick, type 304...
-
Bobrick 24" Straight Grab Bar B-5806 x 24
24" (610mm) long, 1-1/4" (32mm) dia. tubing. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick, type 304...
-
Bobrick 24" Straight Grab Bar B-6806 x 24
24" (610mm) long, 1-1/2" (38mm) dia. tubing. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick, type 304...
-
Sec.36.504 Relief
Sec.36.504 Relief.
-
1 [§ 4.7.3]
1 [§ 4.7.3] Only measure the width of the ramp section of the curb ramp (labeled “ramp” to the right [below]). The ramp section of a curb ramp is also known as the “ramp run.” If...
-
§382.57(a)(5)(ii)
(ii) Maintained in proper working condition.
-
2 [§§ 4.7.2; 4.8.2; 4.1.6(3)(a)]
2 [§§ 4.7.2; 4.8.2; 4.1.6(3)(a)] The running slope of the curb ramp is the slope in the direction that people travel when going up or down the ramp run. The arrow in the...
-
1007.8.2 Directions
1007.8.2 Directions. Directions for the use of the two-way communication system, instructions for summoning assistance via the two-way communication system and written identification...
-
13 [§ 4.7.10]
13 [§ 4.7.10] A corner-type curb ramp is located at the center (or apex) of a corner and is often aligned to direct users into the middle of an intersection. As the illustration...
-
1007.8.1 System requirements
1007.8.1 System requirements. Two-way communication systems shall provide communication between each required location and a central control point location approved by the fire...
-
§382.65 What are the requirements concerning on-board wheelchairs?
[See subsections ...]
-
382.1 What is the purpose of this Part?
382.1 What is the purpose of this Part? The section is amended to include foreign carriers.
-
1016.8 Resting Intervals
Resting intervals shall comply with 1016.8.
-
1016.8.1 Length
The resting interval length shall be 60 inches (1525 mm) long minimum.
-
Question 8
YES/NO 8. Are the lower edges of all objects that hang over the sidewalks or walkways (e.g., banners, strings of lights) 80 inches or more above the...
-
604.9.7 Toilet Compartments
Toilet compartments shall comply with 604.8.
-
List of Subjects in 36 CFR Part 1195
Health care, Individuals with disabilities, Medical devices.
-
604.9.7 Toilet Compartments
Toilet compartments shall comply with 604.8.
-
Technical Requirements [1016]
[See subsections ...]
-
Cross Slope [1016.7.2]
Cross slope is the side-to-side slope of the surface of an ORAR. When the surface is constructed of concrete, asphalt, or boards, the cross slope must be no steeper than 1:48 (2...
-
§ 382.57(a)(5)(ii)
(ii) Maintained in proper working condition.
