Requires the Premium User plan or above.
(Login or upgrade your account!)
Search Results "Ramp Surface"
Filters
Commonly Searched Documents
-
World Dryer SLIMdri™ Surface-Mounted ADA Compliant Hand Dryer Front Elevation
-
American Specialties Roval™ Collection Surface Mounted Paper Towel Dispenser Model 20210
Requires the Premium User plan or above. (Login or upgrade your account!) -
American Specialties Stainless Steel Surface Mounted Paper Cup Dispenser Model 0002-SM
Requires the Premium User plan or above. (Login or upgrade your account!) -
Bobrick MatrixSeries Surface-Mounted Multi-Roll Toilet Tissue Dispenser B-5288 Elevations
Requires the Premium User plan or above. (Login or upgrade your account!) -
Bobrick Extra-Heavy-Duty Surface-Mounted Towel Bar B-530 x 18
Requires the Premium User plan or above. (Login or upgrade your account!) -
Bobrick Extra-Heavy-Duty Surface-Mounted Towel Bar B-530 x 24
Requires the Premium User plan or above. (Login or upgrade your account!) -
American Specialties Turbo-Dri Jr. Surface Mounted High-Speed Dryer Model 0198
Requires the Premium User plan or above. (Login or upgrade your account!) -
Bradley Surface Mounted Stainless Steel Single Roll Toilet Tissue Dispenser 5084 Plan
Requires the Premium User plan or above. (Login or upgrade your account!) -
American Specialties Dual Roll Surface Mounted Toilet Paper Holder Model 7305-2
Requires the Premium User plan or above. (Login or upgrade your account!) -
American Specialties Surface Mounted Twin Hide-A-Roll Toilet Tissue Dispenser Model 0030
Requires the Premium User plan or above. (Login or upgrade your account!) -
Accessible Routes
The accessible route must comply with ADAAG provisions for the location, width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level...
-
19.1 Q. If a sliding door track has a threshold of 3/4, does this trigger requirements for ramps?
A. No. The Guidelines at Requirement 4 provide that thresholds at doors, including sliding door tracks, may be no higher than 3/4 and must be beveled with a slope no greater than 1:2.
-
Feature 1 - Parking and Passenger Drop-Off Areas
In order to be usable, the access aisle must be level, clear of gravel or mud, and the surface must be in good condition without wide cracks or broken pavement....
-
Edge Protection [4.8.7]
A rail mounted close enough to the ramp surface to prevent passage of a 4 inch diameter sphere can function like a curb in keeping front casters from getting stuck on vertical posts and...
-
406.7 Islands
Raised islands in crossings shall be cut through level with the street or have curb ramps at both sides....
-
ACCESSIBLE ROUTE
Interior accessible routes may include corridors, hallways, floors, ramps, elevators and lifts....
-
ACCESSIBLE ROUTE
Interior accessible routes may include corridors, hallways, floors, ramps, elevators and lifts....
-
ACCESSIBLE ROUTE
Interior accessible routes may include corridors, hallways, floors, ramps, elevators and lifts....
-
Back Support: ADA Standard Section 903.4
Back support shall be 42 inches (1065 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (455 mm) minimum above the seat...
-
§ 38.101(a)
(a) Any stepwell or doorway with a lift, ramp or bridge plate shall have, when the door is open, at least 2 footcandles of illumination measured on the step tread, ramp, bridge plate, or...
-
11B-502.6.4 Marking
Each accessible car and van space shall have surface identification complying with either Section 11B-502.6.4.1 or 11B-502.6.4.2....
-
§ 38.119(a)
(a) Any stepwell, or doorway with a lift, ramp or bridge plate, shall have, when the door is open, at least 2 foot-candles of illumination measured on the step tread, ramp, bridge plate...
-
INTRODUCTION
The failure to install accessible curb ramps at locations where no curb ramps exist, or where inaccessible curb ramps exist, within the time required by applicable federal disability access...
-
Parking sign height measurement technique
502.6 says "Signs shall be 60 inches (1525 mm) minimum above the finish floor or ground surface measured to the bottom of the sign." But which floor or ground surface? ...
