them from outside the vehicle while starting to board, and to continue to use them throughout the boarding process, and shall have the top between 30 inches and 38 inches above the ramp surface...
Search Results "Walking Surface"
Filters
Commonly Searched Documents
-
§ 38.83(c)(8) Handrails
-
§ 38.125(c)(8) Handrails
grasp them from outside the car while starting to board, and to continue to use them throughout the boarding process, and shall have the top between 30 inches and 38 inches above the ramp surface...
-
Rebuilding Together Portland - Portland, OR
Rebuilding Together Portland organizes over 1,700 volunteers from all walks of life to unite on the last Saturday in April each year to complete roughly $1,250,000 worth of improvements...
-
M305.2.7 Clearance (Section-by-Section Analysis)
Specifically, the Access Board sought input from the public in question 22, on whether transfer supports on diagnostic equipment could provide 1½ inches minimum clearance around the gripping surface...
-
6.3 Minority Reports
6.3 Minority Reports Because the Advisory Committee did not achieve consensus on the recommendation for a minimum transfer surface height standard, U.S....
-
11B-809.12 Electrical receptacles, controls and switches
When the reach is over a kitchen work surface and base cabinet, the work surface shall be 36 inches (914 mm) maximum above the finish floor and 25 1/2 inches (650 mm) maximum in depth....
-
M305.3 Standing Supports (Section-by-Section Analysis)
The Access Board sought public input in questions 39 and 40 in the MDE NPRM preamble on whether the cross section dimensions for gripping surfaces should be applied to standing supports...
-
M301.4.2 Clearance Around Base (Section-by-Section Analysis)
The proposed rule required a minimum clearance of 6 inches high measured from the floor and 36 inches deep measured from the edge of the examination surface. NPRM, 77 FR at 6927....
-
Introduction
Four static body dimensions considered relevant to the width and depth dimensions of a seating surface were computed and analyzed to serve as a reference....
-
Trail Study Sites
The SEWF surfaces were originally developed for use as impact-sensitive playground surfaces....
-
1133A.7.1 Plumbing protection
There shall be no sharp or abrasive surfaces under kitchen sinks....
-
405.9.2 Curb or Barrier
curb or barrier shall be provided that prevents the passage of a 4 inch (100 mm) diameter sphere, where any portion of the sphere is within 4 inches (100 mm) of the finish floor or ground surface...
-
Technical Requirements [1017]
The technical requirements for trails include specific provisions for the surface, clear tread width, passing spaces, tread obstacles, openings, running slope, cross slope, resting intervals...
-
T402.8.1 Deployment to Roadways or to Curb Height Boarding and Alighting Areas
bridgeplates used for deployment to the roadway or to curb-height boarding and alighting areas shall be 1:6 maximum, as measured to ground level with the non-rail vehicle resting on a flat surface...
-
TRANSIT BOARDING PLATFORM
[DSA-AC] A horizontal, generally level surface, whether raised above, recessed below or level with a transit rail, from which persons embark/disembark a fixed rail vehicle....
-
405.9.2 Curb or Barrier
curb or barrier shall be provided that prevents the passage of a 4 inch (100 mm) diameter sphere, where any portion of the sphere is within 4 inches (100 mm) of the finish floor or ground surface...
-
1133A.2, Item 3
A clear floor space at least 30 inches (762 mm) by 48 inches (1219 mm) that allows either a parallel or a forward approach shall be provided at the work surface required by Section 1133A...
-
1002.5.2 Transfer Height
The height of amusement ride seats designed for transfer shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area....
-
Note
As shown, there are several ways for grab bars to be designed with adequate gripping surfaces, while ensuring that nothing can be tied onto them....
-
Grab Bar Height
The Board has clarified that the height of grab bars is measured to the top of the gripping surface (609.4)....
-
Mirrors
Provide a mirror in the Spy City Café men's and women's toilet rooms where the bottom edge of the reflecting surface of the mirror is mounted no more than 40" above the finished floor....
-
R305.2.7 Boarding and Alighting Areas
At boarding and alighting areas at sidewalk or street level transit stops for rail vehicles, detectable warning surfaces shall be placed at the side of the boarding and alighting area facing...
-
SECTION#5
SECTION#5 For the following questions, please answer every item pertaining to the trail surface installation. Leave blank if the response choice is not applicable to you....
-
Can guards or collars be attached to handrails to prevent skateboard traffic?
No, handrail gripping surfaces at egress stairs subject to the Standards must be unobstructed on the top and sides and free of sharp or abrasive elements so that users can maintain a continuous...
