Amusement rides designed primarily for children, amusement rides that are controlled or operated by the rider, and amusement rides without seats, are not required to provide wheelchair spaces, transfer...
Search Results "End Transfer Surface"
-
11B-216.12 Amusement rides
-
Rockwood Manufacturing Company 11047 Series 47 Straight Single Bar Set 8" Pull CTC
Metal: T4 Back to Back and Concealed; Pull Free End = 6, Push Free End = 6, Common End = 5....
-
11B-224.2 Guest rooms with mobility features
Provide either a bathtub complying with Section 11B-607 or a transfer type shower complying with Section 11B-608.2.1. 2. ...
-
§ 37.131(a)(2)(ii)
(ii) At end stations and other stations in outlying areas, the entity may designate circles with radii of up to 11/2 miles as part of its service area, based on local circumstances....
-
5 Key Warranty Features to Compare Before Hiring a Roofer
Third, look for transferability. A warranty that can be transferred to a new homeowner is a huge selling point if you decide to move....
-
Adjustable height protocol
,96%] of the sample (107/116) could transfer at a height of 22” (50.8cm)....
-
Guldmann GLS5 Active lifter
One lift for many functions: Sit to stand Sit to stand transfer from chair to chair Sit to stand transfer from bed to chair Sit to stand transfer from chair...
-
Counter: ADA Standard Section 904.3.2
The counter surface height shall be 38 inches (965 mm) maximum above the finish floor or ground....
-
11B-904.3.2 Counter
The counter surface height shall be 38 inches (965 mm) maximum above the finish floor or ground....
-
11B-904.3.2 Counter
The counter surface height shall be 38 inches (965 mm) maximum above the finish floor or ground....
-
1. Common Problems and Solutions in Website Accessibility
Resources providing more detailed information on accessible website design are provided at the end of this Chapter....
-
Terminal
Device or software with which the end user directly interacts and that provides the user interface....
-
Terminal
Device or software with which the end user directly interacts and that provides the user interface....
-
Terminal
Device or software with which the end user directly interacts and that provides the user interface....
-
Terminal
Device or software with which the end user directly interacts and that provides the user interface....
-
STORY
[DSA-AC] That portion of a building or facility designed for human occupancy included between the upper surface of a floor and upper surface of the floor or roof next above....
-
11B-705.2 Detectable directional texture
transit boarding platforms shall comply with Figure 11B-705.2 and shall be 0.1 inch (2.5 mm) in height that tapers off to 0.04 inch (1.0 mm), with bars raised 0.2 inch (5.1 mm) from the surface...
-
11B-705.2 Detectable directional texture
transit boarding platforms shall comply with Figure 11B-705.2 and shall be 0.1 inch (2.5 mm) in height that tapers off to 0.04 inch (1.0 mm), with bars raised 0.2 inch (5.1 mm) from the surface...
-
STORY
[DSA-AC] That portion of a building or facility designed for human occupancy included between the upper surface of a floor and upper surface of the floor or roof next above....
-
Landscape Forms Inc. FLO 3 Section Bike Rack
May be embedded or surface mounted at ends Nylon glides cushion the surface contact point of 2 intermediate loops Refer to installation guide to meet APBP Guidelines for bike rack spacing...
-
A.2.ii. - Should EIT be compatible with assistive technology?
These products, such as information kiosks, copiers, or other similar products that do not permit a user to install or connect assistive technology, must be designed so that an end user...
-
2010 ADA Standards
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....
-
104.1.1 Construction and Manufacturing Tolerances
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....
-
104.1.1 Construction and Manufacturing Tolerances
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....
