[2010 ADA Standards] 502.5 Vertical Clearance....
Search Results "ADA Compliance"
-
11B-502.5 Vertical clearance
-
11B-216.11 Check-out aisles
[2010 ADA Standards] 216.11 Check-Out Aisles....
-
11B-604.4 Seats
[2010 ADA Standards] 604.4 Seats....
-
11B-604.4 Seats
[2010 ADA Standards] 604.4 Seats....
-
11B-904.4.1 Parallel approach
[2010 ADA Standards] 904.4.1 Parallel Approach....
-
TownSteel TDC 90 ALUMINUM Grade 1 Door Closer
diameter Maximum Door Opening Regular arm 180°， Parallel arm 180°， Top jamb 180° Finish Aluminum (AL) and Duro (DU) stock finishes, other upon request Warranty 25 years limited Code Compliance...
-
ASI Global Partitions High Density Polyethylene Solid Plastic Toilet Partitions
Fire Code Compliance: Global Partitions’ Solid Plastic sheet has pass all five parameters of the NFPA 286 fire test criteria. Solid Plastic NFPA 286 Criteria Test Results NEW!...
-
TownSteel TDC 70 ALUMINUM Grade 1 Door Closer
diameter Maximum Door Opening Regular arm 180°， Parallel arm 180°， Top jamb 180° Finish Aluminum (AL) and Duro (DU) stock finishes, other upon request Warranty 25 years limited Code Compliance...
-
TownSteel CS Series, Grade 2, Clutched Flat Rose Cylindrical Locks
Standard, KA, MK, GMK, GGMK, Construction Available Finish US26D, US10B stocked, other upon request Function ANSI F75, F76, F84, F86, F87, F109 stocked, other unpon request Code Compliance...
-
Bradley Diplomat Foam Soap Dispenser 6A01-11
ADA Compliant; Consult local and national accessibility codes for proper installation guidelines....
-
TownSteel TDC 40, CAST IRON Grade 1 Door Closer
diameter Maximum Door Opening Regular arm 120°， Parallel arm 180°， Top jamb 120° Finish Aluminum (AL) and Duro (DU) stock finishes, other upon request Warranty 25 years limited Code Compliance...
-
Sec.36.304(d)(2)
(2) If, as a result of compliance with the alterations requirements specified in paragraph (d)(1) of this section, the measures required to remove a barrier would not be readily achievable...
-
403.5.2 Clear Width at Turn
EXCEPTION: Where the clear width at the turn is 60 inches (1525 mm) minimum compliance with 403.5.2 shall not be required. Figure 403.5.2 Clear Width at Turn...
-
Exceptions [1014.1, Exceptions 1 and 2]
When a condition for exception does not permit full compliance with a specific provision in the technical requirements for camp shelters, the camp shelter must comply with the specific provision...
-
12185(e) Review
the study required by subsection (a) of this section, the Office of Technology Assessment shall provide a preliminary draft of such study to the Architectural and Transportation Barriers Compliance...
-
412.1 General (Section-by-Section Analysis)
Would compliance with section 412 be readily achievable for manufacturers of mobile telecommunications equipment?...
-
4.1.7(1)(a) General Rule
applicable technical specifications of 4.2 through 4.35 and the applicable special application sections 5 through 10 unless it is determined in accordance with the procedures in 4.1.7(2) that compliance...
-
10.2.1(3)
Signs that are sized to the maximum dimensions permitted under legitimate local, state or federal regulations or ordinances shall be considered in compliance with 4.30.2 and 4.30.3 for purposes...
-
LARGE AREA ASSISTIVE LISTENING SYSTEMS (ALS): REVIEW AND RECOMMENDATIONS
Large Area Assistive Listening Systems: Review and Recommendations Final Report to United States Architectural and Transportation Barriers Compliance Board (U.S....
-
3.4.1 General
When a new viewing area is constructed, or an existing viewing area is altered or reconstructed, if a condition for exception in section 1.1 prohibits full compliance with a specific requirement...
-
§100.75(d)
(d) 24 CFR part 109 provides information to assist persons to advertise dwellings in a nondiscriminatory manner and describes the matters the Department will review in evaluating compliance...
-
III-9.4000 Preliminary determination
If the Assistant Attorney General's office decides to proceed, the office will consult with the Architectural and Transportation Barriers Compliance Board....
-
2.3.1
2.3.1 Define the measurement protocols to be used to check for compliance with the tolerances and standards....
-
Small entities potentially affected by proposed standards
discussed below, if an enforcing authority such as DOJ adopts the standards as mandatory requirements for entities subject to its jurisdiction, small health care providers may experience some compliance...
