Diagonal curb ramps with flared sides shall have a segment of curb 24 inches (610 mm) long minimum located on each side of the curb ramp and within the marked crossing....
Search Results "Minimum Dimension"
Filters
Commonly Searched Documents
-
11B-406.5.10 Diagonal curb ramps
-
TECHNICALLY INFEASIBLE
structural frame, or because other existing physical or site constraints prohibit modification or addition of elements, spaces, or features which are in full and strict compliance with the minimum...
-
11B-405.9.1 Reserved
The floor or ground surface of the ramp run or landing shall extend 12 inches (305 mm) minimum beyond the inside face of a handrail complying with 505....
-
219 Assistive Listening Systems
Section 219.3 specifies the minimum number of receivers according to a sliding scale based on the seating capacity of the assembly area....
-
607.4.1.1 Back Wall
Two grab bars shall be installed on the back wall, one located in accordance with 609.4 and the other located 8 inches (205 mm) minimum and 10 inches (255 mm) maximum above the rim of the...
-
1009.5.4 Transfer Steps
The surface of the bottom tread shall extend to a water depth of 18 inches (455 mm) minimum below the stationary water level. Advisory 1009.5.4 Transfer Steps....
-
R407.2 Running Slope
Ramp runs shall have a running slope between 5 percent minimum and 8.3 percent maximum. Advisory R407.2 Running Slope....
-
R406.3 Unobstructed Side Reach
space allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 1220 mm (4.0 ft) maximum and the low side reach shall be 380 mm (1.25 ft) minimum...
-
§ 36.105(d)(2)(iii)
(iii) For example, applying these principles it should easily be concluded that the types of impairments set forth in paragraphs (d)(2)(iii)(A) through (K) of this section will, at a minimum...
-
611.4 Height
Front loading machines shall have the bottom of the opening to the laundry compartment located 15 inches (380 mm) minimum and 36 inches (915 mm) maximum above the finish floor....
-
4.1.5 Accessible Buildings: Additions
Each space or element added to the existing building or facility shall comply with the applicable provisions of 4.1.1 to 4.1.3, Minimum Requirements (for New Construction) and the applicable...
-
4.2.4.2 RELATIONSHIP OF MANEUVERING CLEARANCE TO WHEELCHAIR SPACES
Minimum Clear Floor Space for Wheelchairs...
-
212 Kitchens, Kitchenettes, and Sinks
Minimum number of sinks required when provided....
-
Edge Protection [§405.9]
higher than 6” that have side flares ramp landings serving an adjoining run or stairway sides of ramp landings with vertical drop-offs not exceeding ½” within 10” of the minimum...
-
Clear Floor Space [§309.2]
If clear floor space is obstructed on both sides more than half the minimum required depth, a wider clearance (36” min.) is required for maneuvering and sway....
-
68.79. Contract Providers
November 5, 2001, 26 TexReg 8807; amended effective February 1, 2005, 30 TexReg 382) In addition to the specific terms of their contracts, contract providers are subject to the same minimum...
-
§ 35.108(d)(2)(iii)
(iii) For example, applying these principles it should easily be concluded that the types of impairments set forth in paragraphs (d)(2)(iii)(A) through (K) of this section will, at a minimum...
-
1134A.6, Item 4
The grab bar reinforcement shall be a minimum of 6 inches (152.4 mm) nominal in height....
-
1133A.4.1, Item 4
Two 15-inch (381 mm) wide minimum breadboards may be provided in lieu of the required 30 inches (762 mm) of countertop work surface, and used without meeting the repositioning requirements...
-
11B-704.5 TTY shelf
The shelf shall be capable of accommodating a TTY and shall have 6 inches (152 mm) minimum vertical clearance above the area where the TTY is to be placed....
-
11B-405.9.1 Reserved.
The floor or ground surface of the ramp run or landing shall extend 12 inches (305 mm) minimum beyond the inside face of a handrail complying with 505....
-
Other Power-driven Mobility Devices (OPDMDs)
In deciding whether an OPDMD can be accommodated, the following may be considered: type, size, weight, dimensions, and speed of the device; volume of pedestrian traffic...
-
Accessibility - Flatness and Lippage
Open - graded aggregates for PICP Joint width between paving units (See Figure 1) oto +3/16 in. (5 mm) of the paver manufacturer's recommended joint width dimension Pedestals...
-
Jean Tessmer
Some of us prefer to mount to allow 28" knee clearance minimum to give the person in the wheelchair a lower shelf height of 32" depending on the thickness of your new #200 baby changer shelf...