The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall....
Search Results "Minimum Dimension"
Filters
Commonly Searched Documents
-
610.3.1 Rectangular Seats
-
[A] 101.3 Intent
The purpose of this code is to establish the minimum requirements to safeguard the public health, safety and general welfare through structural strength, means of egress facilities, stability...
-
§ 36.303(g)(4)(i)
(i) A public accommodation shall provide at its movie theaters a minimum of one fully operational audio description device for every two movie theater auditoriums exhibiting digital movies...
-
11B-704.5 TTY shelf
The shelf shall be capable of accommodating a TTY and shall have 6 inches (152 mm) minimum vertical clearance above the area where the TTY is to be placed....
-
704.5 TTY Shelf
The shelf shall be capable of accommodating a TTY and shall have 6 inches (150 mm) minimum vertical clearance above the area where the TTY is to be placed....
-
Sec.36.608 Guidance concerning model codes
developing a model code, the Assistant Attorney General may review the relevant model code and issue guidance concerning whether and in what respects the model code is consistent with the minimum...
-
Technically Infeasible
structural frame; or because other existing physical or site constraints prohibit modification or addition of elements, spaces, or features that are in full and strict compliance with the minimum...
-
407.2.3.2 Car Designations
Tactile characters shall be 2 inches (51 mm) high minimum. Figure 407.2.3.2 Car Designations on Jambs of Destination-Oriented Elevator Hoistway Entrances...
-
F233.3.3.2 Alterations to Individual Residential Dwelling Units
least one other room is altered, the requirements of F233.3.1 shall apply to the altered residential dwelling units until the total number of residential dwelling units complies with the minimum...
-
405.5 Clear Width
The clear width of a ramp run and, where handrails are provided, the clear width between handrails shall be 36 inches (915 mm) minimum....
-
804.2.1 Pass Through Kitchen
appliances or cabinets are opposite a parallel wall, clearance between all opposing base cabinets, counter tops, appliances, or walls within kitchen work areas shall be 40 inches (1015 mm) minimum...
-
I. Introduction
The purpose of this Minority Report is to make a formal recommendation for a minimum transfer surface low height of 19 inches for diagnostic imaging medical equipment....
-
405.9.1 Extended Floor or Ground Surface
The floor or ground surface of the ramp run or landing shall extend 12 inches (305 mm) minimum beyond the inside face of a handrail complying with 505....
-
405.5 Clear Width
The clear width of a ramp run and, where handrails are provided, the clear width between handrails shall be 36 inches (915 mm) minimum....
-
Clear Floor Space
Clear Floor Space The load and unload areas adjacent to transfer devices must have a clear space of 30 by 48 inches minimum....
-
704.5 TTY Shelf
The shelf shall be capable of accommodating a TTY and shall have 6 inches (150 mm) minimum vertical clearance above the area where the TTY is to be placed....
-
T703.1 General
The symbol shall have a background field height of 4 inches (100 mm) minimum. The symbol and its background shall have a non-glare finish....
-
7(2)(b)(v)
(v) Vanities and lavatories are installed with the centerline of the fixture a minimum of 1'3" horizontally from an adjoining wall or fixture....
-
§ 36.303(g)(4)(i)
(i) A public accommodation shall provide at its movie theaters a minimum of one fully operational audio description device for every two movie theater auditoriums exhibiting digital movies...
-
11B-604.8.1.1.3 Maneuvering space with end-opening door
In a wheelchair accessible compartment with a door located in the front wall or partition (facing the water closet), either in-swinging or out-swinging, a minimum 60 inches (1524 mm) wide...
-
4.31.9(2)
The shelf shall be capable of accommodating a text telephone and shall have 6 in (152 mm) minimum vertical clearance in the area where the text telephone is to be placed....
-
404.2.7 Door and Gate Hardware
Operable parts of such hardware shall be 34 inches (865 mm) minimum and 48 inches (1220 mm) maximum above the finish floor or ground....
-
Alterations / Additions
Alterations / Additions The minimum number of accessible patient rooms required is based on the total number of bedrooms that are altered or added, including where a unit or department...