LATCH FACEPLATE -Standard - 1 1/8" x 2 1/4" for 2-3/4" backset. Optional 1" x 2-1/4" for 2-3/8" backset. STRIKES -ASA strike standard, "T" and full lip strike available on request....
Search Results "Latch Side Clearance"
Filters
Commonly Searched Documents
-
Cal-Royal CR6000 Series Digital Touch Screen Door Lock
-
810.6.3 Station Names
Signs shall be clearly visible and within the sight lines of standing and sitting passengers from within the vehicle on both sides when not obstructed by another vehicle....
-
11B-402.2 Components
Accessible routes shall consist of one or more of the following components: walking surfaces with a running slope not steeper than 1:20, doorways, ramps, curb ramps excluding the flared sides...
-
Grab Bars
Grab bars are required on one side wall and the rear wall....
-
402.2 Components
Accessible routes shall consist of one or more of the following components: walking surfaces with a running slope not steeper than 1:20, doorways, ramps, curb ramps excluding the flared sides...
-
Roll-in Access [1014.2.2]
provide roll-in access into a camp shelter, a level or sloped entry route that complies with the technical requirements for an ORAR or trail, as applicable, must be provided along the open side...
-
R309.3 Perpendicular or Angled Parking Spaces
Perpendicular and angled parking spaces permit the deployment of a van side-lift or ramp....
-
402.2 Components
Accessible routes shall consist of one or more of the following components: walking surfaces with a running slope not steeper than 1:20, doorways, ramps, curb ramps excluding the flared sides...
-
608.3.2 Standard Roll-In Type Shower Compartments
Where a seat is provided in standard roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall opposite the seat....
-
5.3.2.1 Size
The clear floor or ground space shall be 60 inches (1525 mm) wide minimum measured parallel with the back of the pit toilet, and 56 inches (1420 mm) deep minimum measured parallel to the sides...
-
5.3.2.1 Size
The clear floor or ground space shall be 60 inches (1525 mm) wide minimum measured parallel with the back of the pit toilet, and 56 inches (1420 mm) deep minimum measured parallel to the sides...
-
Curb Ramps at Intersections
Curb ramps at marked crossings must be wholly contained within the crosswalk, excluding side flares....
-
§ 38.39(b)
width-to-height ratio between 3:5 and 1:1 and a stroke width-to-height ratio between 1:5 and 1:10, with a minimum character height (using an upper case “X”) of 1 inch for signs on the boarding side...
-
11B-402.2 Components
Accessible routes shall consist of one or more of the following components: walking surfaces with a running slope not steeper than 1:20, doorways, ramps, curb ramps excluding the flared sides...
-
11B-206.2.19 Pedestrian street crossings
The curb ramp (excluding any flared sides) or blended transition shall be contained wholly within the width of the pedestrian street crossing served....
-
11B-802.1.2 Width
It should be noted that although side access to the wheelchair space is allowed, companion seating in compliance with Section 11B-802.3 must also be provided adjacent to each wheelchair...
-
11B-810.6.3 Station names
Signs shall be clearly visible and within the sight lines of standing and sitting passengers from within the vehicle on both sides when not obstructed by another vehicle....
-
Service Counters
Does that mean the full depth of the counter, from customer side to employee side? Can a split level counter be used (lower customer side, raised employee side)? ...
-
11B-406.5.3 Landings
The landing clear width shall be at least as wide as the curb ramp, excluding any flared sides, or the blended transition leading to the landing....
-
1008.4.2 Clear Floor or Ground Space
These dimensions apply to either forward or side reaches. The reach ranges are appropriate for use with those play components that children seated in wheelchairs may access and reach....
-
1008.4.2 Clear Floor or Ground Space
These dimensions apply to either forward or side reaches. The reach ranges are appropriate for use with those play components that children seated in wheelchairs may access and reach....
-
A. Measuring Slope and Cross Slope
:slopes tilting side to side) are within the limits allowed by the ADA Standards for Accessible Design ("Standards"). There are three primary ways to determine a given slope: 1....
-
1. Typical Issues for Individuals Who Use Wheelchairs, Scooters, or Other Mobility Devices
Ramps with a vertical rise of more than 6 inches must have handrails on both sides....