The table won’t tip even if all persons sit on one side. Easy walk through access. “Skid” design permits movement without damage to turf. ...
Search Results "Latch Side Clearance"
Commonly Searched Documents
- Pilot Rock XT and XTH Series End Accessible Picnic Table Using Aluminum
- Pilot Rock UT and UTH Series End Accessible Picnic Table Using Steel Tops Seats
- Pilot Rock XT and XTH Series End Accessible Picnic Table - Using Steel Tops and Seats
- Pilot Rock UT and UTH Series End Accessible Aluminum Picnic Table
- Pilot Rock UT and UTH Series End Accessible Picnic Table Using Lumber
-
Doorways
In the final rule, clarification has been added that the 32 inch minimum clearance applies to those doors "providing user passage" into and within guest rooms not required to be accessible...
-
2.5.2.2 International Organization for Standardization (ISO) Standards
Risk management plays a critical and central role in the design of medical devices, and it also ties into IEC 60601-1 and FDA’s expectations for quality systems and premarket clearance or...
-
Toilet Compartments
The clear floor space required for a baby changing table by TAS 902.2 may overlap the water closet clearance based on TAS 604.3.2 since baby changing tables are considered convenience “fixtures...
-
Question 16
What is the optimal clearance needed under a bed to accommodate a mechanical lift?...
-
Locating Controls & Devices: Percent of People Who Can Reach the Matrix Cell Indicated While Holding 5 lb Weight - Forward Approach Power Chair
reaching over an obstruction in relation to the forward-most point, and the negative range implying that the reach target is brought closer to the person (such as on a table with knee clearance...
-
Locating Controls & Devices: Percent of People Who Can Reach the Matrix Cell Indicated While Holding 5 lb Weight - Forward Approach Manual Wheelchair
reaching over an obstruction in relation to the forward-most point, and the negative range implying that the reach target is brought closer to the person (such as on a table with knee clearance...
-
Error/Omission: When a transfer shower is used, it is often larger than the required 36" x 36" size.
Requirement: 4.21.2 Size and Clearances. Except as specified in 9.1.2, shower stall size and clear floor space shall comply with Fig. 35(a) or (b)....
- Sargent 8500 Narrow Design Rim Exit Device
-
212 and 606 Kitchens, Kitchenettes, Lavatories, and Sinks
The 1991 Standards, at section 4.24, and the 2010 Standards, at section 606, both require the clear floor space at sinks to be positioned for a forward approach and knee and toe clearance...
-
4.1.3 Adjustable Height Chairs with and without Footplates
Because these chairs with footplates are adjustable in height, when the chair height is fully lowered, a minimum 2” clearance is required from the floor to the bottom of the footplate as...
- AccessRec DuraDeck 2 Molded Plastic Mat Ground Surface
-
11B-1009.2.3 Clear deck space
On the side of the seat opposite the water, a clear deck space shall be provided parallel with the seat....
-
Areas of Sport Activity
Section 206.2.12 of the 2010 Standards further requires that in court sports the accessible route must directly connect both sides of the court....
-
C. Why are Curb Ramps at Pedestrian Crossings Required?
It is often difficult or impossible for a person using a wheelchair, scooter, walker, or other mobility device to cross a street if the sidewalk on either side of the street ends without...
-
11B-406.6 Islands
Raised islands in crossings shall be cut through level with the street or have curb ramps at both sides....
-
608.5.1 Transfer Type Shower Compartments
In transfer type shower compartments, the controls, faucets, and shower spray unit shall be installed on the side wall opposite the seat 38 inches (965 mm) minimum and 48 inches (1220 mm...
-
R309.2 Parallel Parking Spaces
The sidewalk adjacent to accessible parallel parking spaces should be free of signs, street furniture, and other obstructions to permit deployment of a van side-lift or ramp or the vehicle...
-
R304.3.1 Turning Space
If the turning space is constrained on 2 or more sides, the turning space shall be 1.2 m (4.0 ft) minimum by 1.5 m (5.0 ft)....