In cells having more than 25 beds, at least 5 percent of the beds shall have clear floor space complying with Section 11B-807.2.3....
Search Results "Parking Space"
Commonly Searched Documents
-
11B-232.2.1.1 Beds
-
11B-232.2.1.1 Beds
In cells having more than 25 beds, at least 5 percent of the beds shall have clear floor space complying with Section 11B-807.2.3....
-
11B-232.2.1.1 Beds
In cells having more than 25 beds, at least 5 percent of the beds shall have clear floor space complying with Section 11B-807.2.3....
-
Reach Ranges and Operable Parts
OPERABLE PARTS Forward and side reach 11B-308.2/3 Over projections 11B-308.2.2/3.2 Clear floor space...
-
Reach Ranges and Operable Parts
OPERABLE PARTS Forward and side reach 11B-308.2/3 Over projections 11B-308.2.2/3.2 Clear floor space...
-
1011.2.1 Size and Location
The size and location of the clear ground space shall be in accordance with Table 1011.2.1. ...
-
M102.1 Defined Terms (Section-by-Section Analysis)
decided to add six additional terms to this section; end transfer surface, examination chair, imagining [sic] equipment with bores, imagining [sic] bed, side transfer surface, and wheelchair space...
-
Pilot Rock: Accessible Park Bench & Tables
Requires the Registered User plan or above. Login!
-
Employee Parking Lot
Are employee parking lots considered parking facilities under the 2010 Standards requiring accessible spaces? ...
-
Guidelines for Requirement 2
The Department has retained the applicable provisions of the ANSI Standard for parking space....
-
M305.3.1 Length (Section-by-Section Analysis)
The MDE Advisory Committee supported the proposed technical provisions, but recommended adding additional criteria for standing supports on raised platforms with wheelchair spaces....
-
11B-202.4 Path of travel requirements in alterations, additions and structural repairs
Design professionals frequently note "Existing Accessible Parking," "Existing Accessible Toilets," and similar, which Authorities Having Jurisdiction take to imply that they are compliant...
-
28.1 Q. If an architect or builder chooses to follow the bathroom specifications in Requirement 7...are the other bathrooms in the dwelling unit required to have reinforced walls for grab bars?
A. Yes. Requirement 6 of the Guidelines requires reinforced walls in bathrooms for later installation of grab bars. Even though Requirement 6 was not repeated under Requirement...
-
11B-411.4.7.4 Button spacing
Button spacing shall comply with Section 11B-407.4.7.1.5....
-
1011.2.1 Size and Location
The size and location of the clear ground space shall be in accordance with Table 1011.2.1....
-
Fishing Facilities
Word Fillable Form (0.8MB) Word Non-Fillable Form (0.8MB) PDF Non-Fillable Form (0.7MB)
- Bosch Power Tools - GPL-3 3 Point Laser
-
11B-202.4 Path of travel requirements in alterations, additions and structural repairs
Rearranging toilet partitions to increase maneuvering space. 14. Insulating lavatory pipes under sinks to prevent burns. 15. Installing a raised toilet seat. 16. ...
-
11B-407.4.7.1.5 Button spacing
A minimum clear space of 3/8 inch (9.5 mm) or other suitable means of separation shall be provided between rows of control buttons....
-
M303.3.3.2 Cross Slope
The cross slope of ramp runs shall not be steeper than 1:48.
-
M303.3.3 Ramped
Changes in level greater than ½ inch (13 mm) high shall be ramped and shall comply with M303.3.3.
-
5.8.1.2.4 Edge Protection on Platforms 1½ inches or less in Height
5.8.1.2.4 Edge Protection on Platforms 1½ inches or less in Height. Edge protection is not required on platforms 1 ½ inches or less in height.
-
5.8.1.2.2 Single Ramped Entry - Edge Protection on the Platform and Platform Sides Recommendations
5.8.1.2.2 Single Ramped Entry - Edge Protection on the Platform and Platform Sides Recommendations The Committee recommends a two-inch high edge protection on the back of the...