On blended transitions, detectable warning surfaces shall be placed at the back of curb....
Search Results "Standing Surface"
-
R305.2.3 Blended Transitions
-
3. Medical Diagnostic Equipment
rulemaking (NPRM) to remove the sunset provisions in the our existing accessibility standards for medical diagnostic equipment (MDE) related to the low-height specifications for transfer surfaces...
-
3. Medical Diagnostic Equipment
rulemaking (NPRM) to remove the sunset provisions in the our existing accessibility standards for medical diagnostic equipment (MDE) related to the low-height specifications for transfer surfaces...
-
Chapter 9: Built-In Elements
Chapter 9 covers built-in elements, including dining surfaces and work surfaces (902), benches (903), and sales and service counters (904)....
-
Handrail Extensions
ADAAG does not require handrails on sloped surfaces that have a rise of less than 6 inches or a projection less than 72 inches, or a slope of 1:20 (5%) or less....
-
Acknowledgments
Acknowledgments The development of objective surface measurement devices and objective surface testing was conducted with funding from the National Center for Medical Rehabilitation Research...
-
HEWI Mirror 950.01.300
A continuous mirror, which extends to the edge of the washbasin, is not only suitable for seated users but also for those standing....
-
Kompan, Inc. Hammock ELE400006
The stand-alone Hammock offers children a peaceful place to rest and enjoy their surroundings....
-
Kompan, Inc. Spinner Plate NRO110
The Spinner Plate can be used by 1-3 persons, standing or seated....
-
11B-705.2 Detectable directional texture
transit boarding platforms shall comply with Figure 11B-705.2 and shall be 0.1 inch (2.5 mm) in height that tapers off to 0.04 inch (1.0 mm) , with bars raised 0.2 inch (5.1 mm) from the surface...
-
Gratings [4.5.4]
These requirements apply to gratings located in any walking surface, including courtyards and plazas, not just those on accessible routes....
-
11B-705.2 Detectable directional texture
transit boarding platforms shall comply with Figure 11B-705.2 and shall be 0.1 inch (2.5 mm) in height that tapers off to 0.04 inch (1.0 mm) , with bars raised 0.2 inch (5.1 mm) from the surface...
-
1133A.4.1 Repositionable countertops
Repositionable countertops shall comply with the following: Sinks and work surfaces required by Section 1133A.4 shall be designed to enable repositioning to a minimum height of 28...
-
5.3.2.3 Slope
The slope of the turning space and clear floor or ground space surface shall not be steeper than 1:48 (2 percent) in all directions....
-
SHOPPING CENTER (OR SHOPPING MALL)
. ◼ ETA Editor's Note CBC defines a single, stand alone retail store as a shopping center and, therefore, requires storage mezzanines to be served by an accessible route....
-
1.9.1 Division of the State Architect - Access Compliance.
Examples of temporary buildings or facilities covered include, but are not limited to: reviewing stands, temporary classrooms, bleacher areas, exhibit areas, temporary banking facilities...
-
1.9.1 Division of the State Architect - Access Compliance.
Examples of temporary buildings or facilities covered include, but are not limited to: reviewing stands, temporary classrooms, bleacher areas, exhibit areas, temporary banking facilities...
-
SHOPPING CENTER (OR SHOPPING MALL)
. ◼ ETA Editor's Note CBC defines a single, stand alone retail store as a shopping center and, therefore, requires storage mezzanines to be served by an accessible route....
-
Clearance
Section 403.5 specifies a continuous clearance of 36 inches minimum for walking surfaces....
-
M307.2 Tactilely Discernible (Section-by-Section Analysis)
Patients who are blind or have low vision have difficulty distinguishing a flat membrane button or similar control unless it is tactilely discernible from the surrounding surface and any...
-
904.3.2 Counter
The counter surface height shall be 38 inches (965 mm) maximum above the finish floor or ground....
-
4.34.6.4(1)
(1) The counter shall be mounted at a maximum height of 34 in (865 mm) above the floor, measured from the floor to the top of the counter surface, or shall be adjustable or replaceable as...
-
Location and Size
The side rails are 20 inches minimum in length, 6 inches minimum in height above the table surface, and 1 inch measured horizontally from the adjacent edge of the table surface....
-
3.2 Study Limitations and Other Issues
warning surface and the luminance contrast of the warning surface with adjacent surfaces....
