Secondary exterior door thresholds, including sliding door tracks, shall be 3/4 inch (19.1 mm) high maximum with a 1:2 maximum slope....
Search Results "High Energy Door"
Commonly Searched Documents
-
11B-809.8.1 Door Thresholds
-
404.2.6 Doors in Series and Gates in Series
404.2.6 Doors in Series and Gates in Series....
-
404 Doors, Doorways, and Gates
404 Doors, Doorways, and Gates...
-
4.17.5* DOORS
Toilet stall doors shall comply with 4.13....
-
AUTOMATIC DOOR
A door equipped with a power operated mechanism and controls that open and close the door automatically upon receipt of a momentary actuating signal....
-
AUTOMATIC DOOR
A door equipped with a power operated mechanism and controls that open and close the door automatically upon receipt of a momentary actuating signal....
-
Are closet doors and pantry doors required to comply?
Requirements for doors, doorways, and gates in §404 apply to those that provide “user passage” (§206.5). Doors serving walk-in closets or pantries must comply....
-
11B-411.3.2 Operation
Elevator hoistway and car doors shall open and close automatically....
-
18.1 Q. Is it necessary to provide usable doors when the door leads to an area of the dwelling that is not accessible, such as the door leading down to an unfinished basement...?
Within the dwelling unit, doors intended for user passage through the unit must meet the requirements for usable doors....
-
404.2.6 Doors in Series and Gates in Series
The distance between two hinged or pivoted doors in series and gates in series shall be 48 inches (1220 mm) minimum plus the width of doors or gates swinging into the space....
-
F206.5 Doors, Doorways, and Gates
Doors, doorways, and gates providing user passage shall be provided in accordance with F206.5....
-
206.5 Doors, Doorways, and Gates
Doors, doorways, and gates providing user passage shall be provided in accordance with 206.5....
-
Doors, Doorways and Gates [§206.5 and §404]
Doors, Doorways and Gates [§206.5 and §404] Compliance is required for doors, doorways, and gates providing user passage on accessible routes....
-
R218 Doors, Doorways, and Gates
R218 Doors, Doorways, and Gates The SNPRM would revise R218 to read as follows: R218 Doors, Doorways, and Gates....
-
2. Door Hardware
Is the bathroom door hardware (levers, pulls, etc.) easily operable with one hand, without tight grasping, pinching or twisting of the wrist, since many persons with disabilities may not...
-
404.2.7 Door and Gate Hardware
Handles, pulls, latches, locks, and other operable parts on doors and gates shall comply with 309.4....
- Open Doors Organization (ODO)
-
A4.15.2 Spout Height
Two drinking fountains, mounted side by side or on a single post, are usable by people with disabilities and people who find it difficult to bend over.
-
A4.15.2
Drinking fountains with two spouts can assist both handicapped people and those people who find it difficult to bend over.
-
1010.2.2 Hardware
Door handles, pulls, latches, locks and other operating devices on doors required to be accessible by Chapter 11A or 11B shall not require tight grasping, tight pinching or twisting of the...
-
11B-809.8.3 Door maneuvering clearance.
At the dwelling unit side of the primary entry doors, secondary exterior doors, and required exit doors maneuvering clearances shall be 44 inches (1118 mm) minimum in length measured...
-
404.2.6 Doors in Series and Gates in Series
The distance between two hinged or pivoted doors in series and gates in series shall be 48 inches (1220 mm) minimum plus the width of doors or gates swinging into the space....
-
Door and Signal Timing for Hall Calls [4.10.7], Door Delay for Car Calls [4.10.8]
Timing, based on the distance between the farthest call button and the elevator door, begins with visible and audible signaling of car arrival....
-
Toilet Room Doors
Sections 4.22.2 and 4.22.3 of the 1991 Standards and Section 603.2.3 of the 2010 Standards permit the doors of all toilet or bathing rooms with in-swinging doors to swing into the required...