that covered multifamily dwellings with a building entrance on an accessible route shall be designed and constructed in such a manner that all premises within covered multifamily dwelling units...
Search Results "Hand-Held Shower Unit"
Commonly Searched Documents
-
Requirement 6. Reinforced walls for grab bars.
-
1d
Does the 36" x 48" clear floor space directly outside the shower extend at least 12" past the seat wall of the shower to allow for a seat-to-seat transfer from the wheelchair?...
-
1134A.6 Showers
Showers required to be accessible shall comply with this section....
-
11B-608.2.2.1 Clearance
A 36 inch (914 mm) wide minimum by 60 inch (1524 mm) long minimum clearance shall be provided adjacent to the open face of the shower compartment. [2010 ADAS] 608.2.2.1 Clearance....
-
11B-608.2.2.1 Clearance
A 36 inch (914 mm) wide minimum by 60 inch (1524 mm) long minimum clearance shall be provided adjacent to the open face of the shower compartment....
-
Residential Dwelling Units with Communication Features: ADA Standard Section 233.3.1.2
Section 233.3.1.2 covers scoping requirements in the current ADA Standards for residential dwelling units with communication features.
-
608.2.3 Alternate Roll-In Type Shower Compartments
608.2.3 Alternate Roll-In Type Shower Compartments....
-
11B-809 Residential dwelling units
[See subsections ...]
-
MULTI-BEDROOM HOUSING UNIT
[DSA-AC] A housing unit, intended for use by students at a place of education, with a kitchen and/or toilet and bathing rooms within the unit, such as an apartment, or dormitory....
-
4.8 Outdoor Rinsing Showers
[See subsections ...]
-
11B-610.3.1 Rectangular seats
The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall. The side edge...
-
11B-809.10.6.4 Reinforcement for grab bars
Reinforcement for grabs bars shall comply with the following: Continuous reinforcement shall be installed in the walls of showers 30 inches (762 mm) maximum to 38 inches (965 mm) minimum...
-
11B-608.2.1 Reserved
ETA Editor's Note The transfer type shower compartments prescribed by 2010 ADAS 608.2.1 are not recognized as an accessible shower in California....
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
1. Number of Roll-in Showers
If there are more than 50 guestrooms/suites in the facility, are the proper number of accessible rooms with roll-in showers provided per table 9.1.2 below....
-
Residential Dwelling Units with Communication Features: ADA Standard Section 809.5
Residential dwelling units required to provide communication features shall comply with 809.5....
-
Curbs [4.21.7]
Curbs [4.21.7] Curbs are limited to ½ inch (measured from the room floor and the shower floor) so as not to interfere with entry to the shower....
-
11B-608.2.3 Alternate roll-in type shower compartments
11B-608.2.3 Alternate roll-in type shower compartments....
- Excel Dryer, Inc. CAST Cover Series HANDS ON® Push Button Activated Hand Dryers and Hair Dryers
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
- iStorm Hand Dryer Informational Video
-
Residential Dwelling Units: ADA Standard Section 206.5.4
Section 206.5.4 covers scoping requirements in the most current ADA Standards for accessible routes to residential dwelling units.
-
11B-213.3.6 Bathing facilities
Where two or more accessible showers are provided within the same functional area, at least one shower shall be opposite hand from the other or others (that is, one left-hand controls versus...
-
4.21.7 Curbs
All of the designs reviewed were curbless, roll-in showers....